Samsung SSA-S2100/EXP manual Installing the Wall Mount

Page 14

installation and external connection

INSTALLING THE WALL MOUNT

Follow the instructions below to install the wall mount.

1.Place the wall mount on the installation point and mark the 4 holes for the screws. Drill at least 4 of 6-32 holes.

2.Drill a 1/2” hole on the center of the wall mount.

3.Use 4 screws to ﬁx the wall mount to an appropriate point.

4.Arrange the cables through the center hole.

5.Connect the cable and use one screw on the bottom of the wall mount to ﬁx it to the product.

J Do not install the product on a metal wall. Otherwise, this will cause malfunction due to radio frequency interference against the wall.

14_ installation and external connection

Image 14

Contents Standalone Rfid Access Controller Please visit our websiteSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Input Type Setup Event Memory SetupVoice Volume Setup Default SettingsFeatures Product introductionDoor Open Timeout Alarm External I/O PinsForced Door Open Alarm Duress AlarmWHAT’S Included Quick Guide CD ManualLCD AT a GlanceFront Panel Rear Panel Communication status indicatorPin Connector Preliminary connector for extension LEDCable Color Scheme PIN ConnectorPins Signal Cable Color TCP/IP RJ45 Connector Cable SelectionInstalling the Wall Mount Follow the instructions below to install the wall mountConnecting the Termination Resistor and Diode Bypass Diode ConnectionEARTH-GROUNDING the Communication Cables Host PCConnection Input ConnectionOutput Connection External Reader Connection External Reader ConnectionCommunication Line Connection RS-232 Communication Port ConnectionMax m RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Please follow the steps belowTCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallelInitialization Initializing the system using the Initialize switchSystem Initialization in Master Mode Initializing the SystemTo register a master card To Access the Master ModeRegistering a Master ID 00/00 Name DisplayTo register a master card PIN MAX User Setup User Count SetupLanguage Setup € English € Espanol € PortugueseSET DATE/TIME DATE/TIME SetupCommunication Address Setup Comm Addr SETDefault SET Baud Rate SetupFactory Defaults Baud RateReader #2 Mode Reader mode setupReader #1 Mode Reader #2 KEY Input € USE If set, you can get access using the keypad inputReader #1 KEY Input RD#1 KEY Input not USEUser management Registering ID in Quick ModeQuick Mode Registration To register IDSCANNING… Registering the IDTo register the ID card PW TA TB C RD MA MB LV ID RegisteredSSA-S2101 Numeric letters in 4 ~ 8 or 10 digits To register the PIN numberTo select PIN PW TA TB C RD MA MB LV ID Registered User ManagementID List To Delete IDViewing the ID List ALL ID Clear To cancel the work, press the buttonTo delete all registered IDs To delete all registered master IDs Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W Master ID CLROpen ALR Time User Management Door Open Alarm Time SetupARM/DISARM ARM/DISARM SETTo Check the Number of Events TWO MEN Operation ModeTo move to the TWO MEN Mode item To select USE or not USE, and press ENT . J not USETo Remove ALL Events To Remove the Time ScheduleExit Button Output Time setupDoor Contact Sensor Setup Exit ButtonTime Setup Auxiliary Input #1 SetupAuxiliary Input #2 Setup AUX INPUT#1Tamper Alarm Tamper Alarm Output SetupCUT OFF Output Setup CUT OFF AlarmDuress Mode Output Setup ARM/DISARM Output SetupDoor Open Timeout Setup Output Setup for Level IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 Time Schedule Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Antipassback Error Output SetupOutput Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2Reader #2 ID Error Output Setup Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 12.RD2 ID Error13.RD2 T/S Error Time Setup Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 14.RD2 APB ErrorOutput Time SCHEDULE+ID Advanced setupTime Unit Setup Time Unit Unit 1SEC Unit 0.1SECAPB Mode Not USE ALL Clear Antipassback ModeTime Schedule Setup Use the 4 Buttons to specify the interval, dayHoliday Setup Code 01 Holiday Code SetupHoliday Code Code 10RD1 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD2 Mode I T/SVoice I T/S Output Time Schedule SetupVoice Message Time Schedule T/S Code ‘00’ means no Time Schedules are to be appliedCUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Voice Volume Wiegand Output SetupVoice Volume Setup Wiegand Output not USE Not USEONE Time Read  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features Version CheckInput Test Output TestKeypad Test Last UpdateLCD Test Press ANY KEYMemory Test RAM TESTING…Reader Test Reader Test SCANNING…Communication Test Comm TestO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Other information Menu StructureMenu Structure of the F4 button Menu Structure of the F3 buttonF3 button F4 buttonOther Information Menu Structure of the F5 buttonF5 button Menu Structure of the F6 button F6 buttonMenu Structure of the F7 button Menu Structure of the F8 buttonMenu Structure of the F12 button Menu Structure of the F9 buttonF9 button F12 buttonDuress Alarm Default SettingsOutput Settings for Input Sources TTL#1 TTL#2Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Communication between CardBuzzer keeps beeping Controller and the Host PC failsProduct Specifications Product speciﬁcationsCorrect disposal of batteries in this product