Samsung SSA-S2100/EXP manual To delete all registered IDs, To cancel the work, press the button

Page 35

TO CHECK THE NUMBER OF REGISTERED IDs

You can check the total number of registered IDs.

1.Press the F7 SETUP MENU button.

2. Use the buttons

4 and

6 to move to the REG. ID COUNT item and

5. REG. ID COUNT

press ENT .

 

 

 

 

 

 

 

 

00123

3.The number of registered IDs will be shown on the screen.

MThe number of registered IDs will be displayed in 5 digits.

TO REMOVE ALL REGISTERED IDs

You can remove all of the registered user IDs.

1. Press the F8 SETUP MENU button.

USER MANAGEMENT

2.

Use the buttons

4

and 6 to move to the ALL ID CLEAR item and

 

press ENT .

 

 

3.

Press the button

1

to delete all registered IDs.

• To cancel the work, press the button 0 .

3. ALL ID CLEAR

3.ALL ID CLEAR 1:YES, 0:NO

JPlease upload the ID data to the host PC before deletion, just for backup purposes.

English _ 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Please visit our website Standalone Rfid Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Default Settings Event Memory SetupVoice Volume Setup Input Type SetupProduct introduction FeaturesDuress Alarm External I/O PinsForced Door Open Alarm Door Open Timeout AlarmQuick Guide CD Manual WHAT’S IncludedLCD AT a GlanceFront Panel LED Communication status indicatorPin Connector Preliminary connector for extension Rear PanelCable Color Scheme PIN ConnectorPins Signal Cable Color Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeHost PC EARTH-GROUNDING the Communication CablesInput Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionPlease follow the steps below RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Max mConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionInitializing the System Initializing the system using the Initialize switchSystem Initialization in Master Mode InitializationTo register a master card To Access the Master ModeRegistering a Master ID 00/00 Name DisplayTo register a master card PIN € English € Espanol € Portuguese User Count SetupLanguage Setup MAX User SetupComm Addr SET DATE/TIME SetupCommunication Address Setup SET DATE/TIMEBaud Rate Baud Rate SetupFactory Defaults Default SETReader #2 Mode Reader mode setupReader #1 Mode RD#1 KEY Input not USE € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY InputTo register ID Registering ID in Quick ModeQuick Mode Registration User managementPW TA TB C RD MA MB LV ID Registered Registering the IDTo register the ID card SCANNING…PW TA TB C RD MA MB LV ID Registered User Management To register the PIN numberTo select PIN SSA-S2101 Numeric letters in 4 ~ 8 or 10 digitsID List To Delete IDViewing the ID List ALL ID Clear To cancel the work, press the buttonTo delete all registered IDs Master ID CLR Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W To delete all registered master IDsARM/DISARM SET Door Open Alarm Time SetupARM/DISARM Open ALR Time User ManagementTo select USE or not USE, and press ENT . J not USE TWO MEN Operation ModeTo move to the TWO MEN Mode item To Check the Number of EventsTo Remove the Time Schedule To Remove ALL EventsExit Button Time setupDoor Contact Sensor Setup Exit Button OutputAUX INPUT#1 Auxiliary Input #1 SetupAuxiliary Input #2 Setup Time SetupCUT OFF Alarm Tamper Alarm Output SetupCUT OFF Output Setup Tamper AlarmARM/DISARM Output Setup Duress Mode Output SetupOutput Setup for Level IDs Accessing Reader #1 Door Open Timeout SetupOutput Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 Antipassback Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Time Schedule Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #212.RD2 ID Error Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 Reader #2 ID Error Output Setup14.RD2 APB Error Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 13.RD2 T/S Error Time SetupTime Unit Unit 1SEC Unit 0.1SEC Advanced setupTime Unit Setup Output Time SCHEDULE+IDUse the 4 Buttons to specify the interval, day Antipassback ModeTime Schedule Setup APB Mode Not USE ALL ClearHoliday Setup Code 10 Holiday Code SetupHoliday Code Code 01RD2 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD1 Mode I T/ST/S Code ‘00’ means no Time Schedules are to be applied Output Time Schedule SetupVoice Message Time Schedule Voice I T/SCUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Wiegand Output not USE Not USE Wiegand Output SetupVoice Volume Setup Voice VolumeVersion Check  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features ONE Time ReadOutput Test Input TestPress ANY KEY Last UpdateLCD Test Keypad TestReader Test SCANNING… RAM TESTING…Reader Test Memory TestComm Test Communication TestO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Menu Structure Other informationF4 button Menu Structure of the F3 buttonF3 button Menu Structure of the F4 buttonOther Information Menu Structure of the F5 buttonF5 button F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF12 button Menu Structure of the F9 buttonF9 button Menu Structure of the F12 buttonTTL#1 TTL#2 Default SettingsOutput Settings for Input Sources Duress AlarmOutput Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Controller and the Host PC fails CardBuzzer keeps beeping Communication betweenProduct specifications Product SpecificationsCorrect disposal of batteries in this product
Top Page Image Contents