Samsung SSA-S2100/EXP manual Output Setup for Level 2 IDs Accessing Reader #1

Page 45

Output Setup for Level 2 IDs Accessing READER #1

1.Press the F6 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the RD1 ID OK LV2 item and press ENT .

•The operation time for each output is the same as in “Output Setup for Level 1 IDs Accessing READER #1” above. (see page 44)

2.RD1 ID OK LV2

D R	A R	T 1	T 2	B Z
0 5	0 0	0 0	0 0	0 0

I/O TIME SETUP

Output Setup for Level 3 IDs Accessing READER #1

1.Press the F6 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the RD1 ID OK LV3 item and press ENT .

•The operation time for each output is the same as in “Output Setup for Level 1 IDs Accessing READER #1” above. (see page 44)

3.RD1 ID OK LV3

D R	A R	T 1	T 2	B Z
0 5	0 0	0 0	0 0	0 0

Output Setup for Level 4 IDs Accessing READER #1

1.Press the F6 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the RD1 ID OK LV4 item and press ENT .

•The operation time for each output is the same as in “Output Setup for Level 1 IDs Accessing READER #1” above. (see page 44)

4.RD1 ID OK LV4

D R	A R	T 1	T 2	B Z
0 5	0 0	0 0	0 0	0 0

English _ 45

Image 45

Contents Please visit our website Standalone Rfid Access ControllerSafety information Safety informationImportant Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Voice Volume Setup Event Memory SetupInput Type Setup Default SettingsProduct introduction FeaturesForced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress AlarmQuick Guide CD Manual WHAT’S IncludedAT a Glance Front PanelLCD Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LEDPIN Connector Pins Signal Cable ColorCable Color Scheme Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeHost PC EARTH-GROUNDING the Communication CablesInput Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionRS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps belowConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionSystem Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the SystemTo Access the Master Mode Registering a Master IDTo register a master card Name Display To register a master card PIN00/00 Language Setup User Count SetupMAX User Setup € English € Espanol € PortugueseCommunication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SETFactory Defaults Baud Rate SetupDefault SET Baud RateReader mode setup Reader #1 ModeReader #2 Mode Reader #1 KEY Input € USE If set, you can get access using the keypad inputReader #2 KEY Input RD#1 KEY Input not USEQuick Mode Registration Registering ID in Quick ModeUser management To register IDTo register the ID card Registering the IDSCANNING… PW TA TB C RD MA MB LV ID RegisteredTo select PIN To register the PIN numberSSA-S2101 Numeric letters in 4 ~ 8 or 10 digits PW TA TB C RD MA MB LV ID Registered User ManagementTo Delete ID Viewing the ID ListID List To cancel the work, press the button To delete all registered IDsALL ID Clear Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLRARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SETTo move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USETo Remove the Time Schedule To Remove ALL EventsDoor Contact Sensor Setup Time setupExit Button Output Exit ButtonAuxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF AlarmARM/DISARM Output Setup Duress Mode Output SetupOutput Setup for Level IDs Accessing Reader #1 Door Open Timeout SetupOutput Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID ErrorReader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB ErrorTime Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SECTime Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, dayHoliday Setup Holiday Code Holiday Code SetupCode 01 Code 10Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/SVoice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be appliedInput Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USEONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version CheckOutput Test Input TestLCD Test Last UpdateKeypad Test Press ANY KEYReader Test RAM TESTING…Memory Test Reader Test SCANNING…Comm Test Communication TestInput Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other informationF3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 buttonMenu Structure of the F5 button F5 buttonOther Information F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF9 button Menu Structure of the F9 buttonMenu Structure of the F12 button F12 buttonOutput Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Buzzer keeps beeping CardCommunication between Controller and the Host PC failsProduct speciﬁcations Product SpecificationsCorrect disposal of batteries in this product