Samsung SSA-S2100/EXP manual Antipassback Mode, Time Schedule Setup, APB Mode Not USE ALL Clear

Page 51

1.TIME SCHEDULE T/S CODE: 01 SUN

INTERVAL: 5 12:10 – 15:59

1.TIME SCHEDULE T/S CODE: 01 HOL

INTERVAL: 1 00:00 – 00:00

ANTIPASSBACK MODE

Antipassback mode is used to prevent an identical user from entering or exiting the door twice or more consecutively. This mode is available only with an Exit reader dedicated to detecting exits, which is not available in a system that is solely using the Exit button to exit the door.

1. Press the F2 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the APB MODE item and press
	ENT .
3.	Use the buttons	4	and	6	to select a desired mode and press ENT .

• NOT USE : The Antipassback mode is disabled.

USE : The Anti-Pass Back mode is enabled.

ALL CLEAR! : If entrance or exit is not allowed because of violation of the Anti-Pass Back rules, this will reset the status and resume allowing users to enter or exit the door.

5.APB MODE

J NOT USE

5.APB MODE

JUSE

5.APB MODE

J ALL CLEAR!

ADVANCED SETUP

M The Antipass back mode is set to “NOT USE” by default.

You can conﬁgure the APB error outputs for each reader on the entrance and exit. (Refer to “Antipassback Error Output Setup” at pages 46 and 49.)

TIME SCHEDULE SETUP

You can set a total of 10 Time Schedule codes. The default code is “00”, which is used to allow unlimited access.

Each Time Schedule code has 8 programmable days (Sunday through Saturday, and a holiday), each of which has 5 time intervals.

You can check information such as Time Schedule code, day of the week, time interval and current Time Schedule setting. A holiday in the Time Schedule is linked to a holiday schedule code.

The Time Schedule is based on 24-hour format and therefore “00:00” and “24:00” refer to the same time.

1. Press the F4 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the TIME SCHEDULE item and
	press ENT .					1.TIME SCHEDULE
						T/S CODE: 10 SAT
3.	Use the 4 and	6	, 2	,	8 buttons to specify the interval, day and	INTERVAL:	1
	code and press ENT .					00:00 – 00:00

• T/S CODE : Time Schedule Code 01~10

Weekly : 8 days (HOL,SUN,MON,TUE,WED,THU,FRI,SAT)

INTERVAL : Time interval 1~5

00:00 – 00:00 : hour : min

English _ 51

Image 51

Contents Please visit our website Standalone Rfid Access ControllerSafety information Safety informationImportant Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Default Settings Event Memory SetupVoice Volume Setup Input Type SetupProduct introduction FeaturesDuress Alarm External I/O PinsForced Door Open Alarm Door Open Timeout AlarmQuick Guide CD Manual WHAT’S IncludedAT a Glance Front PanelLCD LED Communication status indicatorPin Connector Preliminary connector for extension Rear PanelPIN Connector Pins Signal Cable ColorCable Color Scheme Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeHost PC EARTH-GROUNDING the Communication CablesInput Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionPlease follow the steps below RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Max mConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionInitializing the System Initializing the system using the Initialize switchSystem Initialization in Master Mode InitializationTo Access the Master Mode Registering a Master IDTo register a master card Name Display To register a master card PIN00/00 € English € Espanol € Portuguese User Count SetupLanguage Setup MAX User SetupComm Addr SET DATE/TIME SetupCommunication Address Setup SET DATE/TIMEBaud Rate Baud Rate SetupFactory Defaults Default SETReader mode setup Reader #1 ModeReader #2 Mode RD#1 KEY Input not USE € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY InputTo register ID Registering ID in Quick ModeQuick Mode Registration User managementPW TA TB C RD MA MB LV ID Registered Registering the IDTo register the ID card SCANNING…PW TA TB C RD MA MB LV ID Registered User Management To register the PIN numberTo select PIN SSA-S2101 Numeric letters in 4 ~ 8 or 10 digitsTo Delete ID Viewing the ID ListID List To cancel the work, press the button To delete all registered IDsALL ID Clear Master ID CLR Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W To delete all registered master IDsARM/DISARM SET Door Open Alarm Time SetupARM/DISARM Open ALR Time User ManagementTo select USE or not USE, and press ENT . J not USE TWO MEN Operation ModeTo move to the TWO MEN Mode item To Check the Number of EventsTo Remove the Time Schedule To Remove ALL EventsExit Button Time setupDoor Contact Sensor Setup Exit Button OutputAUX INPUT#1 Auxiliary Input #1 SetupAuxiliary Input #2 Setup Time SetupCUT OFF Alarm Tamper Alarm Output SetupCUT OFF Output Setup Tamper AlarmARM/DISARM Output Setup Duress Mode Output SetupOutput Setup for Level IDs Accessing Reader #1 Door Open Timeout SetupOutput Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Antipassback Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Time Schedule Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #212.RD2 ID Error Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 Reader #2 ID Error Output Setup14.RD2 APB Error Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 13.RD2 T/S Error Time SetupTime Unit Unit 1SEC Unit 0.1SEC Advanced setupTime Unit Setup Output Time SCHEDULE+IDUse the 4 Buttons to specify the interval, day Antipassback ModeTime Schedule Setup APB Mode Not USE ALL ClearHoliday Setup Code 10 Holiday Code SetupHoliday Code Code 01RD2 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD1 Mode I T/ST/S Code ‘00’ means no Time Schedules are to be applied Output Time Schedule SetupVoice Message Time Schedule Voice I T/SInput Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Wiegand Output not USE Not USE Wiegand Output SetupVoice Volume Setup Voice VolumeVersion Check  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features ONE Time ReadOutput Test Input TestPress ANY KEY Last UpdateLCD Test Keypad TestReader Test SCANNING… RAM TESTING…Reader Test Memory TestComm Test Communication TestInput Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other informationF4 button Menu Structure of the F3 buttonF3 button Menu Structure of the F4 buttonMenu Structure of the F5 button F5 buttonOther Information F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF12 button Menu Structure of the F9 buttonF9 button Menu Structure of the F12 buttonTTL#1 TTL#2 Default SettingsOutput Settings for Input Sources Duress AlarmOutput Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Controller and the Host PC fails CardBuzzer keeps beeping Communication betweenProduct speciﬁcations Product SpecificationsCorrect disposal of batteries in this product