Samsung SSA-S2100/EXP manual LCD Test, Keypad Test, Last Update, Press ANY KEY

Page 61

LCD TEST

This feature allows you to test the LCD status. The SAMSUNG logo will appear rolling up and down. At this time you can check any abnormality in the LCD.

1.Press the F9 SETUP MENU button.

2. Use the buttons

4 and

6 to move to the LCD TEST item and press

4.LCD TEST

ENT .

 

 

 

 

 

Check the SAMSUNG logo.

3.The last date the firmware is amended and the version information is displayed.

LAST UPDATE

v0.50_090803

PRESS ANY KEY

KEYPAD TEST

ADDITIONAL FEATURES

1.Press the F9 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the KEYPAD TEST item and press ENT .

3.When the Keypad Test screen appears, try to press each key one by one. The depressed key will disappear from the screen.

¼ :

ESC

on the keypad

# :

ENT

on the keypad

5.KEYPAD TEST

1 2 3

F 1

F 2

F 3

4 5 6

F 4

F 5

F 6

7 8 9

F 7

F 8

F 9

* 0 # F 1 0 F 1 1 F 1 2

English _ 61

Image 61
Contents Please visit our website Standalone Rfid Access ControllerSafety information Safety informationSafety Information Important Safety InstructionsThis device may not cause harmful interference, Contents Contents Voice Volume Setup Event Memory SetupInput Type Setup Default SettingsProduct introduction FeaturesForced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress AlarmQuick Guide CD Manual WHAT’S IncludedFront Panel AT a GlanceLCD Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LEDPins Signal Cable Color PIN ConnectorCable Color Scheme Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeHost PC EARTH-GROUNDING the Communication CablesInput Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionRS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps belowConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionSystem Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the SystemRegistering a Master ID To Access the Master ModeTo register a master card To register a master card PIN Name Display00/00 Language Setup User Count SetupMAX User Setup € English € Espanol € PortugueseCommunication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SETFactory Defaults Baud Rate SetupDefault SET Baud RateReader #1 Mode Reader mode setupReader #2 Mode Reader #1 KEY Input € USE If set, you can get access using the keypad inputReader #2 KEY Input RD#1 KEY Input not USEQuick Mode Registration Registering ID in Quick ModeUser management To register IDTo register the ID card Registering the IDSCANNING… PW TA TB C RD MA MB LV ID RegisteredTo select PIN To register the PIN numberSSA-S2101 Numeric letters in 4 ~ 8 or 10 digits PW TA TB C RD MA MB LV ID Registered User ManagementViewing the ID List To Delete IDID List To delete all registered IDs To cancel the work, press the buttonALL ID Clear Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLRARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SETTo move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USETo Remove the Time Schedule To Remove ALL EventsDoor Contact Sensor Setup Time setupExit Button Output Exit ButtonAuxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF AlarmARM/DISARM Output Setup Duress Mode Output SetupOutput Setup for Level IDs Accessing Reader #1 Door Open Timeout SetupOutput Setup for Level 3 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID ErrorReader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB ErrorTime Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SECTime Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, dayHoliday Setup Holiday Code Holiday Code SetupCode 01 Code 10Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/SVoice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be appliedInput CUT OFF Check Setup Input Time Schedule SetupCUT OFF SET Event Memory Setup Additional featuresID Display Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USEONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version CheckOutput Test Input TestLCD Test Last UpdateKeypad Test Press ANY KEYReader Test RAM TESTING…Memory Test Reader Test SCANNING…Comm Test Communication TestInput Type Input Type SetupO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other informationF3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 buttonF5 button Menu Structure of the F5 buttonOther Information F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF9 button Menu Structure of the F9 buttonMenu Structure of the F12 button F12 buttonOutput Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Buzzer keeps beeping CardCommunication between Controller and the Host PC failsProduct specifications Product SpecificationsCorrect disposal of batteries in this product