Samsung SSA-S2100/EXP manual Baud Rate Setup, Factory Defaults, Default SET

Page 28

initialization

BAUD RATE SETUP

This product supports 9600, 19200, 38400, and 57600 bps, and it is set to 57600 bps by default.

An improper speed setting can cause a communication error so ensure that you specify the same speed in the same network.

1.Press the F1 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the BAUD RATE item and press
	ENT .
3.	Use the buttons	4	and	6	to select a serial communication speed.

• 9600

19200

38400

57600

4. When done, press ENT to save your settings.

M If you encounter a problem with the communication, check the followings ﬁrst.

-Check the communication addresses for this product and the host PC (software).

-Check the baud rate settings of each of the host PC and this product.

-Check the communication port and cable.

-Check the host PC for the port settings.

8.BAUD RATE 57600

8. BAUD RATE

J19200

8.BAUD RATE 19200

FACTORY DEFAULTS

All menu settings will return to the factory default. (The memory is not deleted.)

1.Press the F8 SETUP MENU button.

2.	Use the buttons	4	and 6 to move to the DEFAULT SET item and press	6. DEFAULT SET
	ENT .
3.	Press the button	1	to restore the menu settings to the default.

• To cancel the resetting, press the button 0 .

6. DEFAULT SET

1:YES, 0:NO

28_ initialization

Image 28

Contents Standalone Rfid Access Controller Please visit our websiteSafety information Safety informationSafety Information Important Safety InstructionsThis device may not cause harmful interference, Contents Contents Event Memory Setup Voice Volume SetupInput Type Setup Default SettingsFeatures Product introductionExternal I/O Pins Forced Door Open AlarmDoor Open Timeout Alarm Duress AlarmWHAT’S Included Quick Guide CD ManualFront Panel AT a GlanceLCD Communication status indicator Pin Connector Preliminary connector for extensionRear Panel LEDPins Signal Cable Color PIN ConnectorCable Color Scheme TCP/IP RJ45 Connector Cable SelectionInstalling the Wall Mount Follow the instructions below to install the wall mountConnecting the Termination Resistor and Diode Bypass Diode ConnectionEARTH-GROUNDING the Communication Cables Host PCConnection Input ConnectionOutput Connection External Reader Connection External Reader ConnectionCommunication Line Connection RS-232 Communication Port ConnectionRS-485 Communication Port Connection Standalone RS-485 Communication Port Connection Multiple UnitsMax m Please follow the steps belowTCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallelInitializing the system using the Initialize switch System Initialization in Master ModeInitialization Initializing the SystemRegistering a Master ID To Access the Master ModeTo register a master card To register a master card PIN Name Display00/00 User Count Setup Language SetupMAX User Setup € English € Espanol € PortugueseDATE/TIME Setup Communication Address SetupSET DATE/TIME Comm Addr SETBaud Rate Setup Factory DefaultsDefault SET Baud RateReader #1 Mode Reader mode setupReader #2 Mode € USE If set, you can get access using the keypad input Reader #1 KEY InputReader #2 KEY Input RD#1 KEY Input not USERegistering ID in Quick Mode Quick Mode RegistrationUser management To register IDRegistering the ID To register the ID cardSCANNING… PW TA TB C RD MA MB LV ID RegisteredTo register the PIN number To select PINSSA-S2101 Numeric letters in 4 ~ 8 or 10 digits PW TA TB C RD MA MB LV ID Registered User ManagementViewing the ID List To Delete IDID List To delete all registered IDs To cancel the work, press the buttonALL ID Clear Duress Mode Duress Mode Not USE Duress Password Enter Duress P/WTo delete all registered master IDs Master ID CLRDoor Open Alarm Time Setup ARM/DISARMOpen ALR Time User Management ARM/DISARM SETTWO MEN Operation Mode To move to the TWO MEN Mode itemTo Check the Number of Events To select USE or not USE, and press ENT . J not USETo Remove ALL Events To Remove the Time ScheduleTime setup Door Contact Sensor SetupExit Button Output Exit ButtonAuxiliary Input #1 Setup Auxiliary Input #2 SetupTime Setup AUX INPUT#1Tamper Alarm Output Setup CUT OFF Output SetupTamper Alarm CUT OFF AlarmDuress Mode Output Setup ARM/DISARM Output SetupDoor Open Timeout Setup Output Setup for Level IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Error Output Setup Reader #1 ID Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output SetupOutput Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2Reader #2 Error Output Setup Output Setup for Level 4 IDs Accessing Reader #2Reader #2 ID Error Output Setup 12.RD2 ID ErrorReader #2 Time Schedule Error Output Setup Reader #2 Antipassback Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB ErrorAdvanced setup Time Unit SetupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SECAntipassback Mode Time Schedule SetupAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, dayHoliday Setup Holiday Code Setup Holiday CodeCode 01 Code 10Reader Mode Time Schedule Reader #1 Mode Time Schedule Reader #2 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/SOutput Time Schedule Setup Voice Message Time ScheduleVoice I T/S T/S Code ‘00’ means no Time Schedules are to be appliedInput CUT OFF Check Setup Input Time Schedule SetupCUT OFF SET Event Memory Setup Additional featuresID Display Wiegand Output Setup Voice Volume SetupVoice Volume Wiegand Output not USE Not USE The default setting for One Time Read is not USE ONE Time Read Not USE Jnot USE Additional FeaturesONE Time Read Version CheckInput Test Output TestLast Update LCD TestKeypad Test Press ANY KEYRAM TESTING… Reader TestMemory Test Reader Test SCANNING…Communication Test Comm TestInput Type Input Type SetupO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Other information Menu StructureMenu Structure of the F3 button F3 buttonMenu Structure of the F4 button F4 buttonF5 button Menu Structure of the F5 buttonOther Information Menu Structure of the F6 button F6 buttonMenu Structure of the F7 button Menu Structure of the F8 buttonMenu Structure of the F9 button F9 buttonMenu Structure of the F12 button F12 buttonDefault Settings Output Settings for Input SourcesDuress Alarm TTL#1 TTL#2Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Card Buzzer keeps beepingCommunication between Controller and the Host PC failsProduct Specifications Product speciﬁcationsCorrect disposal of batteries in this product