Samsung SSA-S2100/EXP manual Reader mode setup, Reader #1 Mode, Reader #2 Mode

Page 29

reader mode setup

READER #1 MODE

READER#1 is the default reader that is built in this product.

1.Press the F1 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the READER#1 MODE item and
	press ENT .
3.	Use the buttons	4	and	6	to select a reader mode.

2 modes are available for your choice.

3.READER#1 MODE ID ONLY

READER MODE

• ID ONLY : In this mode, you can get access only with the proximity card or ID number.

ID+P/W : If configured with this mode, access is granted only when the password is entered after reading the card or entering the ID number.

4. When done, press ENT to save your settings.

3. READER#1 MODE

JID+P/W

3.READER#1 MODE ID+P/W

SETUP

READER #2 MODE

READER#2 is an external reader for exit.

1.Press the F1 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the READER#2 MODE item and
	press ENT .
3.	Use the buttons	4	and	6	to select a reader mode.

2 modes are available for your choice.

• ID ONLY : In this mode, you can get access only with the proximity card or ID number.

ID+P/W : In this mode, you can get access through the password authentication after using the proximity card or entering the ID number.

4.READER#2 MODE ID ONLY

4. READER#2 MODE

JID+P/W

4. When done, press ENT to save your settings.

4. READER#2 MODE

ID+P/W

English _ 29

Image 29

Contents Please visit our website Standalone Rfid Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Voice Volume Setup Event Memory SetupInput Type Setup Default SettingsProduct introduction FeaturesForced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress AlarmQuick Guide CD Manual WHAT’S IncludedLCD AT a GlanceFront Panel Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LEDCable Color Scheme PIN ConnectorPins Signal Cable Color Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeHost PC EARTH-GROUNDING the Communication CablesInput Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionRS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps belowConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionSystem Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the SystemTo register a master card To Access the Master ModeRegistering a Master ID 00/00 Name DisplayTo register a master card PIN Language Setup User Count SetupMAX User Setup € English € Espanol € PortugueseCommunication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SETFactory Defaults Baud Rate SetupDefault SET Baud RateReader #2 Mode Reader mode setupReader #1 Mode Reader #1 KEY Input € USE If set, you can get access using the keypad inputReader #2 KEY Input RD#1 KEY Input not USEQuick Mode Registration Registering ID in Quick ModeUser management To register IDTo register the ID card Registering the IDSCANNING… PW TA TB C RD MA MB LV ID RegisteredTo select PIN To register the PIN numberSSA-S2101 Numeric letters in 4 ~ 8 or 10 digits PW TA TB C RD MA MB LV ID Registered User ManagementID List To Delete IDViewing the ID List ALL ID Clear To cancel the work, press the buttonTo delete all registered IDs Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLRARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SETTo move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USETo Remove the Time Schedule To Remove ALL EventsDoor Contact Sensor Setup Time setupExit Button Output Exit ButtonAuxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF AlarmARM/DISARM Output Setup Duress Mode Output SetupOutput Setup for Level IDs Accessing Reader #1 Door Open Timeout SetupOutput Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID ErrorReader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB ErrorTime Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SECTime Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, dayHoliday Setup Holiday Code Holiday Code SetupCode 01 Code 10Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/SVoice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be appliedCUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USEONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version CheckOutput Test Input TestLCD Test Last UpdateKeypad Test Press ANY KEYReader Test RAM TESTING…Memory Test Reader Test SCANNING…Comm Test Communication TestO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Menu Structure Other informationF3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 buttonOther Information Menu Structure of the F5 buttonF5 button F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF9 button Menu Structure of the F9 buttonMenu Structure of the F12 button F12 buttonOutput Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Buzzer keeps beeping CardCommunication between Controller and the Host PC failsProduct speciﬁcations Product SpecificationsCorrect disposal of batteries in this product