Samsung SSA-S2100/EXP manual User management, Registering ID in Quick Mode, To register ID

Page 31

user management

REGISTERING ID IN QUICK MODE

To register ID

1.Press the F12 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the REGISTRATION item and press ENT .

3.Use one of the following two ways to enter an ID:

•Place the card on the main unit to display the card ID on the screen.

•Use the keypad to enter the number and press ENT .

4.Enter the password and press ENT .

5.ID registration is completed.

•Registering in Quick mode will set TA and TB to 00, and RD, MA, MB, LV to 0. (Refer to page 32.)

(QUICK MODE)

1. REGISTRATION

1.REGISTRATION ID:_

ENTER PIN PUT ID CARD

1.REGISTRATION ID:12345678 PASS WORD:_

USER MANAGEMENT

ID REGISTERED!

English _ 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Please visit our website Standalone Rfid Access ControllerSafety information Safety informationSafety Information Important Safety InstructionsThis device may not cause harmful interference, Contents Contents Default Settings Event Memory SetupVoice Volume Setup Input Type SetupProduct introduction FeaturesDuress Alarm External I/O PinsForced Door Open Alarm Door Open Timeout AlarmQuick Guide CD Manual WHAT’S IncludedFront Panel AT a GlanceLCD LED Communication status indicatorPin Connector Preliminary connector for extension Rear PanelPins Signal Cable Color PIN ConnectorCable Color Scheme Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeHost PC EARTH-GROUNDING the Communication CablesInput Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionPlease follow the steps below RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Max mConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionInitializing the System Initializing the system using the Initialize switchSystem Initialization in Master Mode InitializationRegistering a Master ID To Access the Master ModeTo register a master card To register a master card PIN Name Display00/00 € English € Espanol € Portuguese User Count SetupLanguage Setup MAX User SetupComm Addr SET DATE/TIME SetupCommunication Address Setup SET DATE/TIME Baud Rate Baud Rate Setup Factory Defaults Default SETReader #1 Mode Reader mode setupReader #2 Mode RD#1 KEY Input not USE € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY InputTo register ID Registering ID in Quick ModeQuick Mode Registration User managementPW TA TB C RD MA MB LV ID Registered Registering the IDTo register the ID card SCANNING…PW TA TB C RD MA MB LV ID Registered User Management To register the PIN numberTo select PIN SSA-S2101 Numeric letters in 4 ~ 8 or 10 digitsViewing the ID List To Delete IDID List To delete all registered IDs To cancel the work, press the buttonALL ID Clear Master ID CLR Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W To delete all registered master IDsARM/DISARM SET Door Open Alarm Time SetupARM/DISARM Open ALR Time User ManagementTo select USE or not USE, and press ENT . J not USE TWO MEN Operation ModeTo move to the TWO MEN Mode item To Check the Number of EventsTo Remove the Time Schedule To Remove ALL EventsExit Button Time setupDoor Contact Sensor Setup Exit Button OutputAUX INPUT#1 Auxiliary Input #1 SetupAuxiliary Input #2 Setup Time SetupCUT OFF Alarm Tamper Alarm Output SetupCUT OFF Output Setup Tamper AlarmARM/DISARM Output Setup Duress Mode Output SetupOutput Setup for Level IDs Accessing Reader #1 Door Open Timeout SetupOutput Setup for Level 3 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Antipassback Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Time Schedule Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #212.RD2 ID Error Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 Reader #2 ID Error Output Setup14.RD2 APB Error Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 13.RD2 T/S Error Time SetupTime Unit Unit 1SEC Unit 0.1SEC Advanced setupTime Unit Setup Output Time SCHEDULE+IDUse the 4 Buttons to specify the interval, day Antipassback ModeTime Schedule Setup APB Mode Not USE ALL ClearHoliday Setup Code 10 Holiday Code SetupHoliday Code Code 01RD2 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD1 Mode I T/ST/S Code ‘00’ means no Time Schedules are to be applied Output Time Schedule SetupVoice Message Time Schedule Voice I T/SInput CUT OFF Check Setup Input Time Schedule SetupCUT OFF SET Event Memory Setup Additional featuresID Display Wiegand Output not USE Not USE Wiegand Output SetupVoice Volume Setup Voice VolumeVersion Check  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features ONE Time ReadOutput Test Input TestPress ANY KEY Last UpdateLCD Test Keypad TestReader Test SCANNING… RAM TESTING…Reader Test Memory TestComm Test Communication TestInput Type Input Type SetupO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other informationF4 button Menu Structure of the F3 buttonF3 button Menu Structure of the F4 buttonF5 button Menu Structure of the F5 buttonOther Information F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF12 button Menu Structure of the F9 buttonF9 button Menu Structure of the F12 buttonTTL#1 TTL#2 Default SettingsOutput Settings for Input Sources Duress AlarmOutput Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Controller and the Host PC fails CardBuzzer keeps beeping Communication betweenProduct specifications Product SpecificationsCorrect disposal of batteries in this product
Top Page Image Contents