Samsung AR30JVFUCWKNMG manual Mode, English-16, Press the button on the remote controller

Page 16

mode

For a comfortable sleep, the air conditioner will operate it Fall asleep Sound sleep Wake up from mode.

When the air conditioner is on and in cool/heat (ARJS series) mode

1. Press the button on the remote controller.

indicator appears and Off timer indicator starts blinking on the remote controller display.

2. Press the Time Up or Time Down button to set the time.

You can set the time in half hourly unit from 30 minutes ~ 3 hours and hour unit from 3 hours ~ 12 hours.

Operating hour can be set from minimum 30 minutes to maximum

12 hours.

Default operation hour is set to 8 hours.

3. Press the Set button to active it on.

Off timer indicator stops blinking and reserved time will be displayed for 3 seconds. Then the air conditioner operates in good’sleep mode.

If you don’t press Set button within 10 seconds after pressing the or Time Up or Time Down button, the air conditioner will return to previous status. Check Off timer indicator on the remote controller and indicator on the indoor

unit.

Cancel Press the Cancel button once again.

You can set the desired temperature by 1˚C in the range of 16˚C~30˚C.

Fan speed will be adjusted automatically according to the mode.

However, I f you selectmode while heating operation is on, you can adjust fan speed(ARJSmodel).

When the mode is on.

In Cool mode: Air flow direction will be adjusted automatically.

In Heat mode: Adjusting air flow direction is available. (ARJSmodel).

Temperature and fan speed changes in mode

Fall asleep: Eases you into sleep by dropping the temperature.

Sound sleep: Relaxes your body and raises your temperature slightly.

Wake up from mode: Allows you to wake up from comfortable intermittent air and it makes you feel refreshed.

• Set Off timer in

mode over 5 hours. You fell disturbed sleep if the

is set too short or long

because the default is set to 8-hour-operation.

 

If the mode is set less than 4 hours, the operation will stop at the same time.

If the mode is set over 5 hours, it will run as Wake up stage from the last one hour before it stops.

Recommended set temperature is between 25˚C~27˚C for cooling and 21˚C~23˚C for heating.

English-16

MAX4 AR30JV&JS_IB&IM_DB68-04541A_EN.indd 16

2014/9/26 16:38:43

Image 16
Contents MAX4 AR30JV&JSIB&IMDB68-04541AEN.indd 2014/9/26 Contents Safety precautions English-3For Power Supply English-4For Using English-5English-6 Do not place objects or devices under the indoor unit English-7For Cleaning English-8Operation ranges Checking before useEnglish-9 Main parts Checking the name of the partsEnglish-10 Remote controller buttons Checking the remote controllerEnglish-11 Remote controller display Battery changing timeStoring the remote controller Inserting the batteriesBasic function Press the button to set the desired fan speed Press the button to adjust the temperatureEnglish-14 Adjusting the air flow direction Using the Turbo functionVertical air flow Horizontal air flowPress the button on the remote controller ModeEnglish-16 Press the Time Up or Time Down button to set the timeSetting the On/Off timer Press the On Timer/Off Timer buttonAdditional options available in On timer mode English-17Using the Smart Saver function From the moment you have set the timerEnglish-18 If the air conditioner is on If the air conditioner is offUsing the Auto Clean function Using the Quiet functionWhen the air conditioner is turned on Cool/Heat modeCleaning the air conditioner Cleaning the indoor unitCleaning the outdoor unit heat exchanger Opening the panelCleaning the air filter Removing the Air filterEnglish-21 Dry the Air filter in a ventilated areaEnglish-22 Bio filterBio filter sky-blue English-23 Deodorizing filterDeodorizing filter black Maintaining the air conditioner English-24Troubleshooting Air conditionerDoes not come out English-25Check if you press the Set/Cancel button on the remote Press the Power button or disconnect the power plugMode for 1~2 hours. We do not use smelly components Check the Drains have been cleared Regular MaintenanceGeneral information English-27Choosing the installation location Installing the unitPower supply line, fuse or circuit breaker Indoor unitOutdoor Unit Where sulfide gas existsEnglish-29 When installing more than 1 outdoor unit When the air outlet is towards the wallEnglish-30  Figure DescriptionAccessories Accessories in the indoor unit caseAccessories in the outdoor unit case English-31Fixing the installation plate Optional accessoriesTools required for installation General Tools Tools for test operationsCable specification Connecting the assembly cableConnecting the cable Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryEnglish-34 English-35 Smooth the cut edgesTorque Cut off the remaining foam insulationEvacuating the indoor unit Cutting or extending the pipeEnglish-36 Unscrew the caps at the end of each pipeEnglish-37 Correct InclinedCracked Wall Indoor unit Drain hose Drain hose must notDrain hose installation English-38Two hoses are firmly connected, there is no water leakage Hose tightEvacuating the connected pipes English-39Adding Refrigerant English-40Outer Torque If you use a pipe longer than 5 mEnglish-41 Please fill in with indelible ink the factory refrigerant charge of the product 1975Performing the gas leak tests English-42Outdoor unit installed on the wall by rack Fixing the indoor unit in placeFixing the outdoor unit in place English-43Final Check and Trial Operation English-44How to connect your extended power cables English-45Apply heat to the contraction tube to contract it After tube contraction work is completed, wrap it withTechnical Specifications English-46English-47 Questions or COMMENTS? 0211Air Conditioner
Related manuals
Manual 49 pages 24.33 Kb