•TR342 Round Telescoping Termination Cap
•TS345/TS345P Square Termination Cap
Assemble | Termination | ||||||||
storm collar | |||||||||
Cap | |||||||||
around extended | |||||||||
|
|
|
|
|
|
| |||
termination cap |
|
|
|
|
|
|
| ||
pipe |
|
|
|
|
|
|
| ||
once cap is |
|
|
|
|
|
|
| ||
installed. |
|
|
|
| Do NOT | ||||
|
|
|
|
|
| ||||
|
|
|
|
|
| block air | |||
|
|
|
|
|
| ||||
Caulk gaps between |
|
|
|
|
| holes | |||
storm collar & pipe, |
| Storm | |||||||
and storm collar |
| Collar | |||||||
& chase top. |
|
|
|
|
| 3 clip brackets. | |||
|
|
|
|
| Slip over chase collar | ||||
|
|
|
|
| and attach with screws | ||||
|
|
|
|
|
| provided. | |||
Collar |
|
|
|
|
|
|
| ||
2 in. (51 mm) |
|
|
| 14 1/2 in. (368 mm) | |||||
Minimum Height |
|
|
| ||||||
|
|
|
| Maximum | |||||
|
|
|
|
|
| ||||
Chase Top |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
Chase
Collar
2 in. (51 mm)
Minimum Height
Chase Top
Place waterproof sealer under each flange of the termination cap and on top of each screw to help prevent leaks.
Termination Cap
The last section of pipe must stop between 2 in. (51 mm) above the top of the chase and 4 3/4 in. (121 mm) below the top of the chase.
2 in. (51 mm)
maximum
4 3/4 in. (121 mm) 
maximum
Chase
Chimney
Pipe
Chimney
Pipe
Termination cap pipe and chimney section must overlap
Figure 9.5 Installing a TR342 Round Telescoping Termination Cap
•ST375 Square Termination Cap
Termination cap pipe and chimney section must overlap
ÎFigure 9.7 Installing a TS345/TS345P Square Termination Cap
•TCT375 Terra Cotta Cap
Flange
Termination Cap
Collar
2 in. (51 mm)
Minimum Height
Chase Top
Chimney
Pipe
Place waterproof caulk or sealer under each flange of the termination cap and on top of each screw to help prevent leaks.
The last section of pipe must stop between 2 in. (51
mm)above the top of the chase and 4 3/4 in. (121
mm)below the top of the chase.
2 in. (51 mm)
maximum
4 3/4 in. (121 mm) 
maximum
Chase
| Place waterproof sealer | |
Remove 2 screws | under each flange of the | |
termination cap and on | ||
from front & back | ||
top of each screw to | ||
to lift the top off | ||
help prevent leaks. | ||
| ||
Termination Cap | The last section of pipe | |
| must stop between 2 in. | |
| (51 mm) above top of | |
Collar | chase and 7 in. (178 mm) | |
below top of chase | ||
2 in. (51 mm) | ||
| ||
Minimum Height |
| |
Chase Top | 2 in. (51 mm) | |
| 7 in. (178 mm) | |
| Chase | |
Chimney |
| |
Pipe |
|
Termination cap pipe and chimney section must overlap
Termination cap pipe and chimney section must overlap
ÎFigure 9.6 Installing an ST375 Square Termination Cap
ÎFigure 9.8 Installing a TCT375 Terra Cotta Cap
34 | Heatilator • CL36D, CR36D • 12538 • Rev V • 05/09 |