Heatiator CR36D, CL36D owner manual Reference Materials, Fireplace Dimensions

Page 42

13 Reference Materials

A. Fireplace Dimensions

		4-3/4 in. x 6-5/8 in. O.A.
		KNOCKOUT
17-1/4 in.	42-1/4 in.
	42-1/4 in.			1-1/2 in. SQ.
				1-1/2 in. SQ.
	9 in.	38-1/2 in.		GAS
2-1/2 in.		effective		OPENING
		effective
		height
		height
		22-1/2 in.
		6-3/4 in.
36-5/8 in.		5-7/8 in.	3-1/2 in.	8-1/2 in.
36-5/8 in.		5-7/8 in.	3-1/2 in.
		5-1/4 in.		1-1/2 in. DIA.
		34 in. opening	8 in.	ELECTRICAL
		1/2 in.	8 in.	KNOCKOUT
		13-3/4 in.		KNOCKOUT
		13-3/4 in.

B. Optional Components

		52 in.		66 in.
		(1321 mm)	(1676 mm)		20 in.
		16 in.			20 in.
		(406 mm)			(508 mm)



1/2 in.		HX3 Hearth Extension	1/2 in.		HX4 Hearth Extension


(13 mm)			(13 mm)

Fastener Pack

Inlet	Tube
Assembly	Assembly
2 Wire Ties
AK14	Bi-fold Glass Doors
Outside Air Kit	with End Panel
	DM1436 Series

See your Heatilator dealer for a complete listing of optional components.

42	Heatilator • CL36D, CR36D • 12538 • Rev V • 05/09

Image 42

Contents Wood Burning Fireplace Hot screen/mesh and glass doors will cause burnsFire Risk Listing Label Information/Location GrateNumber Table of Contents Installer GuideUser Guide Limited Warranty Heatilator CL36D, CR36D 12538 Rev V 05/09 Non-Combustible Materials Listing and Code ApprovalsAppliance Certiﬁcation Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOutside Air optional Optional ComponentsWood Fuel Hardwood vs SoftwoodMaintenance and Service Chimney Inspection/CleaningDisposal of Ashes Inspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDesign and Installation Considerations DraftNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Mantel Leg or Wall ProjectionsFrame the Fireplace RequiredPosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsYES Install Outside Air Kit Outside Air InstallationChimney Assembly Chimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstall Chimney Air Kit Install Ceiling FirestopsAssemble Chimney Sections Install Attic Insulation Shield Mm overlapComplete Installation Install FlashingCut out Hole in Roof Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination Cap Shrouds Radiation ShieldField Constructed Shrouds Mailbox Style Shroud radiation shield required Finishing Hearth Extension= 1/k x inches of thickness Finishing Material In. Micore or equivilent insulationCombustible Mantel Mantel50 deg 16 3/4 in. Minimum 14-1/2 39 deg 18 in. Min Wood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsChimney Components Catalog #14-1/2 10-7/8 276 mm Service Parts CL36DParts Contact Information

Related manuals

Manual 48 pages 44.09 Kb