Quadra-Fire 839-1290, 839-1320, 839-1340 For Your Safety Read Before Lighting, Lighting Appliance

Page 38

C. Lighting Appliance

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may

result causing property damage, personal injury or loss of life

A.This appliance has a pilot that must be lit manually. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING, smell around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

*Do not try to light any appliance.

*Do not touch any electric switch, do not use any phone in your building.

*Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

*If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

 

LIGHTING INSTRUCTIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

STOP! Read the safety information above on this label.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Set the thermostat to the lowest setting (if applicable) and turn off

 

 

 

 

 

 

 

 

 

 

the switch at the control panel.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Disconnect the power from the appliance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Open the door of the appliance. May need to remove face/front first.

 

 

 

 

5.

Push in gas control knob slightly and turn clockwise

to the "OFF"

 

 

 

position. Do not force.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.Wait five (5) minutes to clear out any gas. Smell for gas, including near the floor. If you smell gas, STOP! Follow "B" of the safety information above. If you don't smell gas go to the next step.

7.Push gas control knob in and turn counterclockwise to the pilot position. NOTE: Knob cannot be turned unless knob is pushed in slightly. Do not force.

8.PIEZO IGNITER: Press down on the gas control knob in pilot position and simultaneously press the piezo igniter.

(This may take many repetitions for lighting.)

ELECTRONIC IGNITER: If the unit is equipped with an electronic igniter it should begin sparking right away.

9.The pilot should be visible through the door opening.

10.After the pilot is lit, continue holding control knob down for approximately

30 seconds. Release the knob and it will pop back up. Pilot should remain lit.

MILLIVOLT

PILOT HOOD

THERMOCOUPLE

If it goes out, repeat steps 7 through 9.

GENERATOR

* If the knob does not pop up when released, stop and immediately call your

 

 

service technician or gas supplier.

 

 

* If the pilot will not stay lit after several tries, turn the gas control knob

 

 

clockwise

to "OFF" and call your service technician or gas supplier.

 

 

11. Reinstall door and face. Wait five minutes to allow pilot flame to stabilize and establish proper draft.

12.Push down and turn gas control knob counterclockwise to "ON".

13.Push burner rocker switch on the control panel to "ON". If thermostat is to be used, leave switch in "OFF" position and set the thermostat to desired setting.

14.Reconnect electrical power to appliance.

TO TURN OFF GAS TO APPLIANCE

1.Set the thermostat to lowest setting.

2.Turn off all electric power to the appliance if service is to be performed.

3.Push in gas control knob slightly and turn clockwise to "OFF" position.

 

 

 

 

Page 38

Quadra-Fire · Topaz · 7009-113E

January 3, 2007

Image 38
Contents Do Discardnot What to do if you smell gasDo not Discard this Manual Manufactured Date Table of Contents 1Listing and Code Approvals Manufacturer Requirements Requirements for the Commonwealth of MassachusettsBELOW. Keep Clear of ALL Obstructions Inspect Appliance & Components Design & Installation ConsiderationsGetting Started Tools and Supplies NeededClearances Appliance Location and ClearancesSelecting Appliance Location Design Purposes only4Termination Locations Vent Termination Minimum ClearancesAlcove Applications Use of Elbows Vent InformationVenting Components Measuring StandardsVenting Guidelines How to Use the Vent GraphExceptions for Horizontal Installations Vertical Distance from Appliance to 90 ElbowHorizontal Termination Up & Out Installations for Top Vent ConfigurationsType B Rear Installations for Use with Rear Vent Kit Type aRear Vent 203mm Step Vertical TerminationDirect Vent Pipe Wood Screws Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Type a Up & Out Installations for Top Vent Configurations Existing Masonry ChimneyCap Retro Connector Converting to LP Gas Gas InformationFuel Conversions Valve Regulator Replacement Propane Natural GASGas Pressures PressureGas Connection Check for GAS LeaksStanding Pilot Ignition System Wiring Recommendation for WireConnecting to the Appliance Wire Size Max. LengthON/OFF Top to Rear Vent Conversion Appliance SetupRemove Shipping Materials Accessories Leg Leveling SystemFor Both Quartet and Solitaire Fronts Front Installation Fronts shipped attached to faceBrick Installation Positioning the Logs Qty DescriptionMineral Wool Glass Door Assembly Replacement Blower Installation31 Blower Wiring Diagram For TOP or Rear Vent Installations Damper AdjustmentShutter Adjustment Make adjustmentControls Operating InstructionsBefore Lighting Appliance For Your Safety Read Before Lighting Lighting ApplianceAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Troubleshooting Symptom Possible Cause Corrective ActionBe Placed in this Opening Maintaining and Servicing Your Appliance After servicingMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsVent Components Diagram Vent Components List MiscellaneousTopaz Item # DescriptionRD. Service Parts List cont’d BRNR-TOPAZRV-TPZ-CSB RV-TPZ-CCRRV-TPZ-CLG RV-TPZ-CWLCast Parts Individual Pieces RE. Accessories Warranty Policy This page Intentionally Left Blank Quadra-Fire · Topaz · 7009-113E January 3 This page Intentionally Left Blank Dealer Telephone TopazContact Information