Napco Security Technologies GEM-P3200 quick start K1CA Keypad Easy Program Menu, GEM-RP1CAE2/GEM

Page 10

Page 10

Enter user code 001 123 - E3 -

User# User Code

WI818G 10/05

Enter User Codes (Press the Rbutton to set cursor.)

Enter up to 48 User Codes with User Options, Authority Level and Access Control Options (if necessary) for each code. Refer to the tables below and on the next page for available data entries for User Options, Authority Level and Access Control Options. Note: All 48 Users must be assigned to areas in “User Area Options” (Address 2455-2502) in Direct Address Programming. By de- fault, only User 1 is enabled in Area 1 and Area 2. Users 2 - 8 are enabled in Area 1 and users 9 - 16 are enabled in Area 2.

K1CA KEYPAD EASY PROGRAM MENU

Press the Rbutton to set the cursor to the User Code. Use the number buttons 1through 9to enter a code from 3 to 6 digits. Enter up to 6 digits in the first six boxes from left to right for each user code. Valid entries are: 0-9. Note: Press the 0button for a zero. No blank spaces in between; leave blank (•) any trailing boxes. If an “Ambush Code” (Address 0495) is entered, do not program the first two digits of ANY User Code as the same digits entered for the “Ambush Code”.

If the programmed code is less than 6 digits, press the Rbutton to set the cursor to the OPTION/LEVEL.

Refer to the tables below for the available User Option and User Level data entries. Enter the user options data in the left digit. Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than 9, press the G1buttons through the G5buttons for B through F, respectively.

For Keypad Access Control, press the Rbutton once again to program applicable keypads. Refer to the tables

below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–7 data in the left digit. (Press the 0buttons for blank).

 

 

 

 

 

 

 

 

 

USER OPTIONS

 

 

 

 

 

Example: Enter a code of “123456” as

 

 

USER CODE

 

USER

USER

ACCESS CONTROL

“123456” (from left to right).

 

 

 

 

 

(UP TO 6 DIGITS)

 

OPTION

LEVEL

 

KEYPADS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GEM-RP1CAE2/GEM-

USER OPTIONS

DATA

BLOCKED

USER

BYPASS

OVERVIEW

ENTRIES

VIEW

PROGRAM

 

 

 

 

 

 

 

blank (•)

 

DISABLED

 

 

 

 

 

 

1

Y

 

 

 

 

 

 

 

 

2

 

Y

 

 

 

 

 

 

 

3

Y

Y

 

 

 

 

 

 

 

4

 

 

Y

 

 

 

 

 

 

5

Y

 

Y

 

 

 

 

 

 

6

 

Y

Y

 

 

 

 

 

 

7

Y

Y

Y

 

 

 

 

 

 

8

 

 

 

Y

 

 

 

 

 

9

Y

 

 

Y

 

 

 

 

 

0

 

Y

 

Y

 

 

 

 

 

B

Y

Y

 

Y

 

 

 

 

 

C

 

 

Y

Y

 

 

 

 

 

D

Y

 

Y

Y

 

 

 

 

 

E

 

Y

Y

Y

 

 

 

 

 

F

Y

Y

Y

Y

 

 

 

 

 

DATA

AUTHORITY

CODE

ENTRIES

LEVEL

TYPE

 

 

 

blank (•)

NONE

ARM/DISARM

 

 

 

1

LEVEL 1

ARM/DISARM

 

 

 

2

LEVEL 2

ARM/DISARM

 

 

 

3

LEVEL 3

ARM/DISARM

 

 

 

4

NONE

ARM ONLY

 

 

 

5

LEVEL 1

ARM ONLY

 

 

 

6

LEVEL 2

ARM ONLY

 

 

 

7

LEVEL 3

ARM ONLY

 

 

 

8

NONE

SERVICE

 

 

 

9

LEVEL 1

SERVICE

 

 

 

0

LEVEL 2

SERVICE

 

 

 

B

LEVEL 3

SERVICE

 

 

 

C*

NONE

AMBUSH

 

 

 

D*

LEVEL 1

AMBUSH

 

 

 

E*

LEVEL 2

AMBUSH

 

 

 

F*

LEVEL 3

AMBUSH

 

 

 

*Note: These entries are only

ACCESS CONTROL KEYPADS

DATA

K.P. 5

K.P. 6

K.P. 7

ENTRIES

 

 

 

 

 

 

 

blank (•)

 

NONE

 

 

 

 

 

1

Y

 

 

 

 

 

 

2

 

Y

 

 

 

 

 

3

Y

Y

 

4

 

 

Y

 

 

 

 

5

Y

 

Y

 

 

 

 

6

 

Y

Y

 

 

 

 

7

Y

Y

Y

 

 

 

 

8

 

 

 

 

 

 

 

9

Y

 

 

 

 

 

 

0

 

Y

 

 

 

 

 

B

Y

Y

 

 

 

 

 

C

 

 

Y

 

 

 

 

D

Y

 

Y

 

 

 

 

E

 

Y

Y

 

 

 

 

F

Y

Y

Y

 

 

 

 

ACCESS CONTROL KEYPADS

 

 

 

 

 

DATA

K.P. 1

K.P. 2

K.P. 3

K.P. 4

ENTRIES

 

 

 

 

 

 

 

 

 

blank (•)

 

NONE

 

 

 

 

 

 

1

Y

 

 

 

 

 

 

 

 

2

 

Y

 

 

 

 

 

 

 

3

Y

Y

 

 

4

 

 

Y

 

 

 

 

 

 

5

Y

 

Y

 

 

 

 

 

 

6

 

Y

Y

 

 

 

 

 

 

7

Y

Y

Y

 

 

 

 

 

 

8

 

 

 

Y

 

 

 

 

 

9

Y

 

 

Y

 

 

 

 

 

0

 

Y

 

Y

 

 

 

 

 

B

Y

Y

 

Y

 

 

 

 

 

C

 

 

Y

Y

 

 

 

 

 

D

Y

 

Y

Y

 

 

 

 

 

E

 

Y

Y

Y

 

 

 

 

 

F

Y

Y

Y

Y

 

 

 

 

 

Note: “Y” indicates option is enabled.

available when address 3905

option 8 is enabled.

Note: “Y” indicates option is enabled.

Note: “Y” indicates option is enabled.

XGEM-P3200 Programming Instructions

LNAPCO Security Systems

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Programming Instructions System Ready 01/01/06 1200 AMImportant Note Napco Security Group, IncTable of Contents Introduction System Programming OptionsDownloading from a Computer Customizing a Default Program Easy Menu Driven Program ModeAccessing Dealer Program Mode Easy Menu Driven Program ModeGEM-RP1CAE2/GEM-K1CA Keypad Easy Program Menu Chime 2 Zones Enter Zone # Enable Telco Line Test?Enable Burg Out Chirp? Exit/Entry2 Zones Enter Zone #GEM-RP1CAE2/GEM-K1CA Enable SIA CP-01? Y/NMenu Area Keypads Enter KPsCentral Station Account # GEMRP1CAE2/GEM-K1CA Keypad Easy Program Menu See WI for InfoGEM-RP1CAE2/GEM K1CA Keypad Easy Program MenuEnter user code 001 123 E3 User Authority Level Keypad Display Function Menu GEM-RP1CAE2/GEM-K1CA Keypad EasyProgram Menu Options ExplanationEnter Proximity Card Users for ACM USE only Keypad Easy Program MenuEnter user code 001 123456 User Code ACM Area0 1 E N R O L L a I T # + C S P0 1 0 0 0 0 0 0 0 0 0 0 0 0 0Keypad Easy Dealer Code RE EnterProgram Mode Direct Address Program ModeAddress Mode Displays Direct Address OverviewDirect Address Program Mode2406 ZonesAmbush 09000900 No data yet enteredDirect Address Program Mode Programming Conventions Used in this ManualDELAYS/TIMEOUTS System Delays & Timeouts Address 2407, 2408System Keypad System Codes Address 0490 0495 & 0500 CodesLeft Right CS Receiver 3 Options Format Options0526 CS Receiver 1 Options 0551 CS Receiver 2 OptionsOptions Address 0527-0546 DigitsCS Subscriber ID Numbers Telco 1 CS Telco 2 Subscriber Event ID Numbers Backup ReportingCS Subscriber ID Numbers Address 0650 CS Telco 1 Subscriber OPENING/CLOSING ID NumbersCS Reporting Codes Address 0859 ID Numbers Telco 3 & CS Reporting CodesCS Subscriber ID Numbers Address 0790 CS Telco 3 Subscriber OPENING/CLOSING ID NumbersAreas CS Reporting Codes Address 0870CS Area & System Reporting Options Address 1024 CS Area Reporting OptionsCS Zone Reporting Codes Address 0910 Reporting CodesCS Zone CS User Reporting Codes CS User Reporting Codes Address 1030Users Global System Trouble Reporting Options Global System Trouble Reporting Options Address 1082System Response Area 1 System EVENT/TROUBLE Area System Trouble Reporting Options Address 1120Area System Trouble Reporting Options Activated by AreaZ10 Zone Options / Zones 1 16 Address 1200Zone Options / Zones Z12 Z13 Z14 Z15 Z16Z22 Z23 Zone Options / Zones 17 32 Address 1402Z19 Z20 Z26 Z27 Z28 Z29 Z30 Z31Zone Options / Zones 33 48 Address 1602 See Zone Options onZone Options / Zones 1- 48 Address 1200 2417 System Options 2416 System Options Enable Day Zone WatchSystem Options Address 2415 2419 System Options2422 System Options ALARM/TROUBLE Reporting Codes Address 3880System Options Address 2420 2422, 3874, 3905, 3880 3874 System OptionsSystem Options Reserved System Options Address 3882 -3901, 3903 3905System Options Left Data ValuesKeypad Options Address 2425 ACM Global Flags Address ACM Timeouts Address 2782ACM Zone Options Address 2740 ACMACM Door Area Options Address 2784 ACM Scheduled Free Access Address 4072ACM Scheduled Free Access ACM Door Area OptionsAddress 2425 ACM OptionsKeypad Home Area / ACM Door #1 Area HEX Address Device TypeSystem Options Address Emergency Free Access AddressSystem Option User Area Options Address 2455 User Area OptionsEZM Type Data Option Entries EZM Group Options Address 2555EZM PGM Terminal Control Group Addr A1 3184 System Options Enable Keypad Area Arming Options & Remote Access LoggingRemote Access Logging Address Area Arming Options Address 2650Turns OFF Disarming AreaArea Output Select the number of receivers Tion. Press Uor Dto saveExternal Relay Control Relay Event Options Relay # Area External Relay ControlCond Areas Controlling Relay Shutoff on Disarm Right Data Entry Relay # Area Timeout Event IDRelay Mapping Data Entries Relay # Left Right NoneEvent ID Codes Data Entries Option Area 1 Keypad AmbushNumber of Relay Board Modules Address Relay Event Alarm Type Options Left Data Timeout EntriesRelay Control MODE--USER Program Mode User Program ModeSystem Reset Options Address 4091 Direct Address ProgramUser Codes Accessing User Program ModeUser Program Mode Programming User Codes with GEM-K1CA KeypadZone Descriptions GEM-RP1CAE2 / GEM-K1CA Keypads Press Characters Displayed Hold G SequenceKeypad Installation Keypad Configuration ModeConfiguring the Keypads New Compat # Program Control MessageAlphabetical Index CS Receiver Telephone Number 1-3Alphabetical Index Contd Keypad System Codes Address 0490-0495 & 0500-0502 Hour Zone Zone OPTION, 30, 31 Address Number Index Address Number Index Contd Global System Trouble Reporting OptionsClosing Report only on COND. Closing AUTO-BYP VERI-PHONE Zones Priority Over Alarms ALARM/TROUBLE Reporting Codes WI818G 10/05 Page GEM-P3200 Wiring Diagram
Top Page Image Contents