Napco Security Technologies GEM-P3200 quick start Keypad Configuration Mode, Keypad Installation

Page 55

WI818G 10/05

KEYPAD CONFIGURATION MODE

Page 55

GEMINI

#OF ZONES IN AREA 1 ENTER # ZONES XX

US

 

 

DSTAT

 

ARME

NEXT/YES

A123

E

 

 

D F

B 456

PRIOR/NO

AREA

C7890G

COMPUTERIZED SECURITY SYSTEM

This section will focus on configuring the GEM-RP1CAe2/GEM-K1CA Keypads. If there is more than one keypad in the system, only Keypad No. 1 may be used for programming.

KEYPAD INSTALLATION

Two types of keypads may be used with the GEM-P3200: the GEM-RP1CAe2/GEM-K1CA. Each must be assigned an address number (1–7) and each requires its own configuration procedure (see CONFIGURING THE KEYPADS, which follows, and DIRECT ADDRESS KEYPAD AREA OPTIONS). At least 1 keypad must be used; only 1 is required for a single-area Commercial Burglary installation.

GEM-RP1CAe2/GEM-K1CA- is a 2-line combination fire/burglary/access keypad capable of supporting 4 EZM zones and a PGM output. The GEM-RP1CAe2 or GEM-K1CA is recommended for use as Keypad #1. See "Important Note" on page 2 for more information regarding the various buttons on the GEM-RP1CAe2/GEM-K1CA keypads.

CONFIGURING THE KEYPADS

A total of up to 7 keypads may be connected to the panel.

Configuring the GEM-RP1CAe2/GEM-K1CA Keypad

Each GEM-RP1CAe2/GEM-K1CA keypad must be configured for (a) keypad tactile beep; (b) entry sounder; (c) keypad address; (d) compatibility number; (e) EZM address; and (f) zone response.

To enter the Keypad Configuration Mode:

 

1.

Move jumper JP1 (located in the center of the control panel board) from Pins 1-2 (top two) to Pins 2-3 (bottom

NORMAL

 

two). NOTE: See Wiring Diagram on page 68.

2.

After about 15 seconds, the display will read “XX OUT OF SYSTEM”, where XX indicates the keypad address.

KEYPAD

3.

Press 11123Rand proceed as follows. (Repeat the following procedure for

CONFIGURE

all keypads).

Keypad Beep

ON

Keypad Tactile Beep

Upon entering the Keypad Configuration Mode, “KEYPAD BEEP ON” will be displayed, indicating that the tactile beep, which sounds when any button is pressed, is on.

To turn off the tactile beep, press the Ubutton (the Ubutton will toggle the tac- tile beep on and off). Press Rto continue or press Cto exit.

Entry Sounder

ON

Entry Sounder

To turn off the keypad entry sounder during entry time, press U(the Ubutton will toggle the entry sounder on and off). Press Rto continue or press Cto exit.

Keypad Address

01

Keypad Address

If more than one keypad is installed, each must be assigned a unique keypad address (that is, no two keypads may be numbered alike):

Keypads must be numbered consecutively (missing numbers are not permitted)

Only Keypad No. 1 may be used for programming.

To assign the keypad number, proceed as follows:

1.Enter the assigned keypad number 01–07, then press Uto save. A valid

number will be acknowledged by a short beep; an invalid number will be re- jected by a long beep.

2.Press Rto continue or press Cto exit.

LNAPCO Security Systems

XGEM-P3200 Programming Instructions

Image 55
Contents System Ready 01/01/06 1200 AM Programming InstructionsNapco Security Group, Inc Important NoteTable of Contents Introduction System Programming OptionsDownloading from a Computer Easy Menu Driven Program Mode Easy Menu Driven Program ModeAccessing Dealer Program Mode Customizing a Default ProgramGEM-RP1CAE2/GEM-K1CA Keypad Easy Program Menu Exit/Entry2 Zones Enter Zone # Enable Telco Line Test?Enable Burg Out Chirp? Chime 2 Zones Enter Zone #Area Keypads Enter KPs Enable SIA CP-01? Y/NMenu GEM-RP1CAE2/GEM-K1CASee WI for Info GEMRP1CAE2/GEM-K1CA Keypad Easy Program Menu Central Station Account #GEM-RP1CAE2/GEM K1CA Keypad Easy Program MenuEnter user code 001 123 E3 Options Explanation GEM-RP1CAE2/GEM-K1CA Keypad EasyProgram Menu User Authority Level Keypad Display Function MenuUser Code ACM Area Keypad Easy Program MenuEnter user code 001 123456 Enter Proximity Card Users for ACM USE only0 0 0 0 0 0 I T # + C S P0 1 0 0 0 0 0 0 0 0 1 E N R O L L aDealer Code RE Enter Keypad EasyDirect Address Overview Direct Address Program ModeAddress Mode Displays Program ModeZones Address Program Mode2406 DirectNo data yet entered 09000900 AmbushProgramming Conventions Used in this Manual Direct Address Program ModeDELAYS/TIMEOUTS System Delays & Timeouts Address 2407, 2408System Keypad System Codes Address 0490 0495 & 0500 CodesLeft Right 0551 CS Receiver 2 Options Format Options0526 CS Receiver 1 Options CS Receiver 3 OptionsAddress 0527-0546 Digits OptionsCS Telco 1 Subscriber OPENING/CLOSING ID Numbers CS Telco 2 Subscriber Event ID Numbers Backup ReportingCS Subscriber ID Numbers Address 0650 CS Subscriber ID Numbers Telco 1CS Telco 3 Subscriber OPENING/CLOSING ID Numbers ID Numbers Telco 3 & CS Reporting CodesCS Subscriber ID Numbers Address 0790 CS Reporting Codes Address 0859CS Area Reporting Options CS Reporting Codes Address 0870CS Area & System Reporting Options Address 1024 AreasCS Zone Reporting Codes Address 0910 Reporting CodesCS Zone CS User Reporting Codes CS User Reporting Codes Address 1030Users Global System Trouble Reporting Options Address 1082 Global System Trouble Reporting OptionsActivated by Area Area System Trouble Reporting Options Address 1120Area System Trouble Reporting Options System Response Area 1 System EVENT/TROUBLEZ12 Z13 Z14 Z15 Z16 Zone Options / Zones 1 16 Address 1200Zone Options / Zones Z10Z26 Z27 Z28 Z29 Z30 Z31 Zone Options / Zones 17 32 Address 1402Z19 Z20 Z22 Z23See Zone Options on Zone Options / Zones 33 48 Address 1602Zone Options / Zones 1- 48 Address 1200 2419 System Options 2416 System Options Enable Day Zone WatchSystem Options Address 2415 2417 System Options3874 System Options ALARM/TROUBLE Reporting Codes Address 3880System Options Address 2420 2422, 3874, 3905, 3880 2422 System OptionsLeft Data Values System Options Address 3882 -3901, 3903 3905System Options System Options ReservedKeypad Options Address 2425 ACM ACM Timeouts Address 2782ACM Zone Options Address 2740 ACM Global Flags AddressACM Door Area Options ACM Scheduled Free Access Address 4072ACM Scheduled Free Access ACM Door Area Options Address 2784Address Device Type ACM OptionsKeypad Home Area / ACM Door #1 Area HEX Address 2425System Options Address Emergency Free Access AddressSystem Option User Area Options User Area Options Address 2455EZM Type Data Option Entries EZM Group Options Address 2555EZM PGM Terminal Control Group Addr A1 Area Arming Options Address 2650 Area Arming Options & Remote Access LoggingRemote Access Logging Address 3184 System Options Enable KeypadTurns OFF Disarming AreaArea Output Tion. Press Uor Dto save Select the number of receiversExternal Relay Control Relay Event Options Relay # Area External Relay ControlCond None Relay # Area Timeout Event IDRelay Mapping Data Entries Relay # Left Right Areas Controlling Relay Shutoff on Disarm Right Data EntryArea 1 Keypad Ambush Event ID Codes Data Entries OptionNumber of Relay Board Modules Address Relay Event Alarm Type Options Left Data Timeout EntriesRelay Control Direct Address Program User Program ModeSystem Reset Options Address 4091 MODE--USER Program ModeProgramming User Codes with GEM-K1CA Keypad Accessing User Program ModeUser Program Mode User CodesPress Characters Displayed Hold G Sequence Zone Descriptions GEM-RP1CAE2 / GEM-K1CA KeypadsKeypad Installation Keypad Configuration ModeConfiguring the Keypads Program Control Message New Compat #CS Receiver Telephone Number 1-3 Alphabetical IndexAlphabetical Index Contd Keypad System Codes Address 0490-0495 & 0500-0502 Hour Zone Zone OPTION, 30, 31 Address Number Index Global System Trouble Reporting Options Address Number Index ContdClosing Report only on COND. Closing AUTO-BYP VERI-PHONE Zones Priority Over Alarms ALARM/TROUBLE Reporting Codes WI818G 10/05 Page GEM-P3200 Wiring Diagram