Napco Security Technologies GEM-P3200 quick start Keypad Easy, Dealer Code RE Enter

Page 14

MENU

Page 14

KeyFob Transmitters as Zone Input Devices

(Refer to display above: press the PRIOR button to go backwards).

Each of the 4 keyfob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 = point 3; A2 = point 4. Up to 48 keyfobs (using 1 button) or 24 keyfobs (using 2 buttons) or 14 keyfobs (using all 4 buttons) or any combination up to a maximum of 48 controlled zones can be assigned, providing multiple wireless panic buttons on a system, each reporting to a Central Station or a pager and/or annunciating on a keypad the keyfob zone number with a description. To assign a keyfob to a zone: program the keyfob as you would a transmitter, entering the keyfob's ID code, check sum and point number at the appropriate zone. The “Quick Method” is not allowed. The zone may be hardwired to an electrical sensor as well as assigned to a keyfob (either one will activate the zone alarm output). NOTE: If assigning a keyfob to a zone, the “ON/OFF” buttons on the keyfob will no longer arm/disarm the system. The keyfob is converted to a “panic only” device.

Enter Zone Descriptions

001 -

 

Press 1and 2to place the cursor and; press

 

 

 

3and 6to select the character.

 

(Direct Entry)

For each zone, enter a description of up to two lines.

 

Press Uto save each description.

 

 

 

WI818G 10/05

 

 

DATA

AUX 1/AUX 2 OPTIONS

ENTRY

 

0

None

1

Relay Group 1 Toggle

2

Relay Group 2 Toggle

9

Panic

A

Auxiliary

B

Instant

C

Aux. Output Toggle

D

Access on Aux. Output

E

Arm STAY ("K Series"

 

Keypads Only)

F

Interior Bypass

 

("Classic" RP Series

 

 

PROGRAM

To proceed to the next description, place the cursor under the Zone Number (e.g. “01”) and change the Zone Number using 3and 6. Program new description as above.

NOTE: Zone Descriptions can only be entered through the GEM-RP1CAe2 Keypad or by using the Napco Quickloader Software. See Easy Menu Programming Worksheet for available zone description characters.

KEYPAD EASY

Enter Date

( / / )

(Direct Entry)

Enter Time

( : )

(Direct Entry)

Enter Date (Press Rto set cursor).

Enter the current date in the format MM/DD/YY. (MM = month, DD = day and YY = year.

Press Uto save. Press the NEXT/YES button to proceed.

Enter Time (Press Rto set cursor.)

Enter the current time in format HH:MMA/P, where HH=hours (01–12); MM=minutes (00–59).

Select AM or PM by pressing any number button to toggle selection.

Press Uto save. Press the NEXT/YES button to proceed.

RP1CAE2/GEM-K1CA

Dealer Code 456789

DEALER CODE RE - ENTER

Dealer Code

Directly enter the Dealer Code (default = 456789), using 0through 9buttons.

Press Uto save.

Re-enter the Dealer Code to verify the previous code.

Press Uto save.

Press the NEXT/YES button to proceed.

GEM-

EXIT DEALER PROGRAM MODE: This completes the custom default program. Press Cto enter the Direct Address Program Mode for further programming or press Conce again to end all programming and resume normal keypad operation.

CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press Cto enter the Address Program Mode; (b) access Location 4091 (Clear Program) or 4093 (Cold Start); (c) press Uand then (d) press Cto exit the Dealer Program Mode. A “SYSTEM TROUBLE/E09-00 SERVICE” will occur. Press Cto silence the keypad.

 

 

 

 

Clear Dealer Program (Erases Dealer Program)

 

4091

XX

H

Use this feature to erase the Panel Program, while maintaining Scheduled Data and Zone Descriptions. Access

 

 

 

 

address 4091 and press U. Data entry is not allowed. NOTE: Enter Easy Menu Driven Program Mode

 

 

 

 

to reprogram system.

 

 

 

 

Cold Start (Erases Entire Program)

 

4093

XX

H

 

This erases all programmed data (Dealer Program, Zone Description Data and Schedules). Access ad-

 

 

 

 

dress 4093 and press U. Data entry is not allowed. NOTE: Some features (schedules) can only be pro-

 

 

 

 

 

 

 

 

grammed again with the Downloading Software.

XGEM-P3200 Programming Instructions

LNAPCO Security Systems

Image 14
Contents Programming Instructions System Ready 01/01/06 1200 AMImportant Note Napco Security Group, IncTable of Contents Downloading from a Computer System Programming OptionsIntroduction Customizing a Default Program Easy Menu Driven Program ModeAccessing Dealer Program Mode Easy Menu Driven Program ModeGEM-RP1CAE2/GEM-K1CA Keypad Easy Program Menu Chime 2 Zones Enter Zone # Enable Telco Line Test?Enable Burg Out Chirp? Exit/Entry2 Zones Enter Zone #GEM-RP1CAE2/GEM-K1CA Enable SIA CP-01? Y/NMenu Area Keypads Enter KPsCentral Station Account # GEMRP1CAE2/GEM-K1CA Keypad Easy Program Menu See WI for InfoEnter user code 001 123 E3 K1CA Keypad Easy Program MenuGEM-RP1CAE2/GEM User Authority Level Keypad Display Function Menu GEM-RP1CAE2/GEM-K1CA Keypad EasyProgram Menu Options ExplanationEnter Proximity Card Users for ACM USE only Keypad Easy Program MenuEnter user code 001 123456 User Code ACM Area0 1 E N R O L L a I T # + C S P0 1 0 0 0 0 0 0 0 0 0 0 0 0 0Keypad Easy Dealer Code RE EnterProgram Mode Direct Address Program ModeAddress Mode Displays Direct Address OverviewDirect Address Program Mode2406 ZonesAmbush 09000900 No data yet enteredDirect Address Program Mode Programming Conventions Used in this ManualSystem System Delays & Timeouts Address 2407, 2408DELAYS/TIMEOUTS Left Right CodesKeypad System Codes Address 0490 0495 & 0500 CS Receiver 3 Options Format Options0526 CS Receiver 1 Options 0551 CS Receiver 2 OptionsOptions Address 0527-0546 DigitsCS Subscriber ID Numbers Telco 1 CS Telco 2 Subscriber Event ID Numbers Backup ReportingCS Subscriber ID Numbers Address 0650 CS Telco 1 Subscriber OPENING/CLOSING ID NumbersCS Reporting Codes Address 0859 ID Numbers Telco 3 & CS Reporting CodesCS Subscriber ID Numbers Address 0790 CS Telco 3 Subscriber OPENING/CLOSING ID NumbersAreas CS Reporting Codes Address 0870CS Area & System Reporting Options Address 1024 CS Area Reporting OptionsCS Zone Reporting CodesCS Zone Reporting Codes Address 0910 Users CS User Reporting Codes Address 1030CS User Reporting Codes Global System Trouble Reporting Options Global System Trouble Reporting Options Address 1082System Response Area 1 System EVENT/TROUBLE Area System Trouble Reporting Options Address 1120Area System Trouble Reporting Options Activated by AreaZ10 Zone Options / Zones 1 16 Address 1200Zone Options / Zones Z12 Z13 Z14 Z15 Z16Z22 Z23 Zone Options / Zones 17 32 Address 1402Z19 Z20 Z26 Z27 Z28 Z29 Z30 Z31Zone Options / Zones 33 48 Address 1602 See Zone Options onZone Options / Zones 1- 48 Address 1200 2417 System Options 2416 System Options Enable Day Zone WatchSystem Options Address 2415 2419 System Options2422 System Options ALARM/TROUBLE Reporting Codes Address 3880System Options Address 2420 2422, 3874, 3905, 3880 3874 System OptionsSystem Options Reserved System Options Address 3882 -3901, 3903 3905System Options Left Data ValuesKeypad Options Address 2425 ACM Global Flags Address ACM Timeouts Address 2782ACM Zone Options Address 2740 ACMACM Door Area Options Address 2784 ACM Scheduled Free Access Address 4072ACM Scheduled Free Access ACM Door Area OptionsAddress 2425 ACM OptionsKeypad Home Area / ACM Door #1 Area HEX Address Device TypeSystem Option Emergency Free Access AddressSystem Options Address User Area Options Address 2455 User Area OptionsEZM PGM Terminal Control Group Addr A1 EZM Group Options Address 2555EZM Type Data Option Entries 3184 System Options Enable Keypad Area Arming Options & Remote Access LoggingRemote Access Logging Address Area Arming Options Address 2650Area Output Disarming AreaTurns OFF Select the number of receivers Tion. Press Uor Dto saveExternal Relay Control Cond External Relay ControlRelay Event Options Relay # Area Areas Controlling Relay Shutoff on Disarm Right Data Entry Relay # Area Timeout Event IDRelay Mapping Data Entries Relay # Left Right NoneEvent ID Codes Data Entries Option Area 1 Keypad AmbushRelay Control Relay Event Alarm Type Options Left Data Timeout EntriesNumber of Relay Board Modules Address MODE--USER Program Mode User Program ModeSystem Reset Options Address 4091 Direct Address ProgramUser Codes Accessing User Program ModeUser Program Mode Programming User Codes with GEM-K1CA KeypadZone Descriptions GEM-RP1CAE2 / GEM-K1CA Keypads Press Characters Displayed Hold G SequenceConfiguring the Keypads Keypad Configuration ModeKeypad Installation New Compat # Program Control MessageAlphabetical Index CS Receiver Telephone Number 1-3Alphabetical Index Contd Keypad System Codes Address 0490-0495 & 0500-0502 Hour Zone Zone OPTION, 30, 31 Address Number Index Address Number Index Contd Global System Trouble Reporting OptionsClosing Report only on COND. Closing AUTO-BYP VERI-PHONE Zones Priority Over Alarms ALARM/TROUBLE Reporting Codes WI818G 10/05 Page GEM-P3200 Wiring Diagram