GE 60-960-95 Freeze Alarm partition 1: 06107, partition 2, Siren Options Menu, Immediate Beeps

Page 50
Freeze Alarm (partition 1: 06107, partition 2: 06207)

Freeze Alarm (partition 1: 06107, partition 2: 06207)

Reporting-Partition 1-2 (Default = off)

 

 

This setting determines whether the panel reports a freeze alarm to the central station or pager, when the selected partition’s energy saver module detects a temperature that matches a predetermined setting (see BUS DEVICES—UNITID—ENERGYOPTIONS—FREEZE TEMP).

￿To turn Freeze Alarm reporting off or on:

1.With the desired partition selected, press A or B until the display shows FREEZE ALARM OFF/ON (current setting).

2.Press 1 (off) or 2 (on). The display flashes the entered setting.

3.Press # and the display shows the new setting.

Alarm Verify (partition 1: 06108, partition 2: 06208)

Reporting-Partition 1-2 (Default = off)

 

 

This setting determines whether the panel reports to the central monitoring station after a single sensor or zone trip (off) or waits for a second trip before reporting (on).

This setting affects sensors/zones in groups 10 through 20. If Alarm Verify is set to on, group 18 responds the same as group 17 (see “Appendix B, Table B1 “Sensor Group Characteristics”).

Note

For UL Listed installations, Alarm Verify must be set to off.

￿To turn Alarm Verify off or on:

1.With the display showing ALARM VERIFY OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting.

2.Press # and the display shows the new setting.

System Tamper (partition 1: 06109, partition 2: 06209)

Reporting-Partition 1-2 (Default = off)

 

 

This setting determines how the panel handles possible tamper situations. When this feature is on, the panel reacts in the following two ways:

•The system goes into alarm if several attempts are made to disarm the system with incorrect access codes (40 consecutive keypresses).

•The panel reports to the central station if a bus device stops communi- cating with the panel.

￿To change the System Tamper setting:

1.With the display showing SYSTEM TAMPER OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting.

2.Press # and the display shows the new setting.

Siren Options Menu

The SIREN OPTIONS menu lets you set up siren operation and supervision.

The following describes how to program the siren option settings that appear under GLOBAL.

Immediate Beeps (0700)

Siren Options-Global (Default = off)

 

 

This setting determines whether the panel activates trouble beeps as soon as a wireless device supervisory condition is detected (on), or if the panel waits until “supervisory time” to activate trouble beeps (off). (Refer to

TIMERS—GLOBAL—SUPERVISORY TIME).

Note

For UL Listed installations, this feature must be on.

￿To turn Immediate Beeps off or on:

1.With the display showing IMMEDIATE BEEPS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting.

2.Press # and the display shows the new setting.

Disable Trouble Beeps (0701)

Siren Options-Global (Default = off)

 

 

When this setting is on, the panel will not beep to alert users of wireless device supervisory trouble.

Note

For UL Listed installations, Disable Trouble Beeps must be set to off.

￿To turn Disable Trouble Beeps off or on:

1.With the display showing DISABLE TR BEEPS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting.

2.Press # and the display shows the new setting.

45

Concord Ultra

Page 49 Page 51
Image 50
Page 49 Page 51
Contents 6HFXULW\ Installation InstructionsConcord Ultra 466-2061Rev CFCC Part 15 Class B NoticesFCC Part 15 Information to the User ACTA PartInstalling the System ContentsPlanning the Installation About This ManualTesting the System Programming the PanelTroubleshooting Special Installation Requirements UL Listed InstallationsRequired Setting TestingDefault SIA System RequirementsCentral Station Reporting Planning the InstallationUL Canada Listed Installations FunctionSuperBus 2000 Touchpads Supervised Wireless SirenStandard Panel SnapCardsSuperBus 2000 8Z Input Module HIM SuperBus 2000 Cellular Backup ModuleSuperBus 2000 Wireless Gateway Module SuperBus 2000 4-RelayOutput Module HOMWire Length Total System Power and Wire Length GuidelinesPower Determine the Panel LocationWire Type Table 2: Total System Wire Length AllowedMax. Wire Length Total System WireTable 3: Minimum Device Current Draw Table 4: Wire RequirementsMounting the Panel Installing Antennas Identify Panel ComponentsFigure 4. Installing the Antennas Connecting the Panel to Earth GroundInstalling Optional SnapCards Figure 5. Connecting the Panel to Earth GroundConnecting 2-WireSmoke Detectors Connecting Detection Devices to Panel Zone InputsConnecting Intrusion Detection Devices Table 5 Panel Minimum Available Power Connecting SpeakersConnecting 4-WireSmoke Detectors 15-WattSpeakerConnecting Piezo Sirens Hardwire Interior SpeakerInterior Sirens Installing Supervised Wireless SirensExterior Sirens 1.Power up the panel see “Powering Up the Panel” Installing SuperBus 2000 Modules SuperBus 2000 Phone Interface/Voice ModuleWiring-Speaker SuperBus 2000 Energy Saver ModuleSuperBus 2000 8Z Input Module SuperBus 2000 Cellular Backup ModuleSuperBus 2000 Automation Module SuperBus 2000 4-RelayOutput ModuleInstalling an RJ-31XPhone Jack SuperBus 2000 Wireless Gateway ModuleSetting Device Address on SuperBus 2000 Devices Figure 21. Connecting the SuperBus to the PanelConnecting the AC Power Transformer the Panel Powering Up the PanelProgramming Entering Program ModeTable 6: Touchpad Button Functions Touchpad Button Programming FunctionsMoving Through Program Mode Tiers and Menus Figure 26. Tier 1 Program MenusProgramming Tier 1 Menu Items Security-GlobalDefault = Using Shortcut NumbersInstaller Code Security-GlobalDefault =Security-GlobalDefault = none Access Code LockSIA False Alarm Reduction Security-GlobalDefault = onSecurity-Partition 1-2Default = on Security-Partition 1-2Default = onSecurity-Partition 1-2Default = on Quick Exit partition 1: 0012, partition 2:Security-Partition 1-2Default = none Keyswitch Sensor partition 1: 0015, partition 2:Keyswitch Style partition 1: 0016, partition 2: Security-Partition 1-2Default = transitionPhones-CSPhone 1-3Defaults: CS Phones-CSPhone 1-3Defaults: CSRPTS OFF/ON current setting, press RPTS OFF/ON current setting, pressphone 3: phone 3:Phones-PagerPhone 1-5Default = on Phones-CSPhone 1-3Defaults: CSPhones-PagerPhone 1-5Default = none Phones-PagerPhone 1-5Default = offLatchkey Rpts pager 1: 0135, pager 2: 0145, pager 0153, pager 4: 0163, pager 5:0154, pager 4: 0164, pager 5: 0155, pager 4: 0165, pager 5:Phone Options-GlobalDefault = on Auto Test ResetPhones-DownloaderPhone Default = none Phone Options-GlobalDefault = offPhone Options-GlobalDefault = on Cancel MessagePhone Options-GlobalDefault = on Phone Options-GlobalDefault = onPhone Options-GlobalDefault = 15 sec Call Wait CancelRemote Access partition 1: 0211, par Phone Options-GlobalDefault = nonePhone Options-Partition 1-2Default = on Phone Options-Partition 1-2Default = onPhone Options-Partition1 only Default = none Phone Options-Partition 1-2Default = offRF Tx Timeout Phone Access Key partition 1: 0216, partition 2:Timers Menu Phone Options-Partition 1-2Default = #Timers-GlobalDefault 4 sec Activity TimeoutTimers-GlobalDefault = 7 days Timers-GlobalDefault = 24 hoursTimers-Partition 1-2Default = 4 min Siren Timeout partition 1: 0313, partitionTimers-Partition 1-2Default = 4 min Timers-Partition 1-2Default = 22:00 10:00 pmTouchpad Options-Partition 1-2Default = on display shows HOUSE CODE nn-x current settingTouchpad Options-GlobalDefault = none Touchpad Options-Partition 1-2Default = onTouchpad Options-Partition 1-2Default = off Back In ServiceTouchpad Options-Partition 1-2Default = off Reporting-GlobalDefault = offTwo Trip Error Low CPU BatteryBattery Restoral Reporting-GlobalDefault = onReporting-GlobalDefault = off Reporting-GlobalDefault = offReporting-GlobalDefault = off Reporting-GlobalDefault = weeklyReporting-Partition 1-2Default = off Reporting-GlobalDefault =Reporting-GlobalDefault = off Reporting-Partition 1-2Default = offReporting-Partition 1-2Default = off Reporting-Partition 1-2Default = offReporting-Partition 1-2Default = off Reporting-Partition 1-2Default = offDisable Trouble Beeps Freeze Alarm partition 1: 06107, partition 2:Alarm Verify partition 1: 06108, partition 2: Reporting-Partition 1-2Default = offSiren Options-GlobalDefault = off Siren Options-GlobalDefault = offSiren Options-GlobalDefault = Siren Options-Partition1 Default = offLearn Sensors Table 7: How to Trip SensorsSensors Default = none Sensors Default = none Sensors Default = noneSensors Default = none Sensor TextAudio Verification-Partition1 Default = Access TimeoutAudio Verification-Partition1 Default = off Audio Verification-Partition1 Default = offAudio Verification-Partition1 Default = 02 sec Access CodeAccessory Modules Menu This setting determines how long AVM accessOutput Programming Device IDPartition Assign Status BeepsTemperature Key BeepsFreeze Temp Cellular Systemoutput 3 10112, output Acc. Modules--SnapCards-OutputText Default = noneOutput Text output 1: 10110, output 2: Onboard Options Menurent setting Two Wire SmokeOnboard Options-InputsDefault = off Onboard Options-InputsDefault = offEntering User Programming Mode Onboard Options-Output Text-Output1, 2 DefaultExiting Programming Mode Output Text Output 1-1120,OutputUser Codes-Reg.User Codes-UserNNN Default = none Time and Date Default = 00:00Time and Date Default = 01/01/00 TimePartition Jump 030nnn3 where nnn=user number Direct Bypassing 030nnn1 where nnn=user numberRemote Access 030nnn2 where nnn=user number System Tests 030nnn4 where nnn=user numberUser Codes-SystemMaster Code Default = Latchkey Report 030nnn5 where nnn=user numberUser Codes-PartitionMaster Code Default = none Options Default = onOptions Default = VolumeSet Up Schedules Menu Options Default =Attach Schedules To Events Default = off Set Up Schedules 05XXY, whereDefault = 00:00 XX=schedule 00 thru 15 and3.Press A or B until the desired light appears Energy Saver Default = 90F Attach Schedules To Events Default = offEnergy Saver Default = 50F Attach Lights To Sensors Default =Table 9: Basic Touchpad Commands Basic System CommandsDefault = N/A Downloader ProgrammingTable 9 Basic Touchpad Commands Continued Testing Zones/SensorsIf a Wireless Sensor Does Not Test Table 10: Pager System Event Codes Testing Phone CommunicationTesting Central Station/Pager Communication Table 11: Pager Sensor/Zone Code and NumbersTesting the Energy Saver Module ESM Testing Outputs and SirensTesting Light Control Table 12: System Alarm SoundsAdjusting Touchpad Display Contrast Testing Cellular Backup Communication Table 13: Current Phone Settings2.Check for proper panel and transformer wiring System indicates Sensor/Touchpad nn low battery Central station/pager is not receiving reportsSystem doesn’t go into alarm when zone is tripped Smoke sensor beeps once every 44 seconds Cellular backup report does not occur Module doesn’t communicate with alarm.com Table A1: Wireless Devices Appendix A System Planning WorksheetsTable A2: Hardwire Devices Table A3: Zone and Sensor AssignmentsTable A3: Zone and Sensor Assignments Continued Table A3 Zone and Sensor Assignments Continued Concord UltraSetting Table A4 System Settings Index and RecordSetting reference default Shortcut NoException Reports phones Off Phone Test On Appendix B Reference Tables Table B1: Sensor Group Characteristics Continued Cross-ZoningTable B2: Item Numbers and Sensor Text System Event Table B3: System Event Trigger NumbersTable B4: Sensor Group Event Trigger Numbers DescriptionSensor Group Table B4 Sensor Group Event Trigger NumbersTable B5: Sensor Number Event Trigger Numbers Trigger NoTable B5: Sensor Number Event Trigger Numbers SensorTable B6: System Feature Event Trigger Numbers Table B5: Sensor Number Event Trigger NumbersFeature Table B6: System Feature Event Trigger NumbersTable B7: Response Characteristics Response CharacteristicsNotes for Table B8: Response Numbers Concord UltraConcord Ultra #* # * #To Enter Programming Mode: 8 + Installer or Dealer Code + 0 +Tier 2 Menus Continued #* # * # * # * # * #Concord Ultra #* # * # #* #Timers Concord UltraConcord Ultra #* # Concord UltraDownloader Code SIA False AlarmSoftware Version Central Station ReportsDisarming Exit DelayDialer Abort Delay DownloaderConcord Ultra Optional SuperBus 2000 Module Connections
Top Page Image Contents