Bryant Official Manual for Proper Installation and Operation of 340MAV Furnaces
Page 37

c.Verify furnace model and size. Table 9 can only be used for model 340MAV furnaces with heating sizes of 040 through 120. Table 10 can only be used for model 340MAV furnaces with a heating size of 140.

d.Find installation altitude in Table 9 or 10.

NOTE: For Canada altitudes of 2000 to 4500 ft, use U.S.A. altitudes of 2001 to 3000 ft in Table 9 or 10.

e.Find closest natural gas heat value and specific gravity in Table 9 or 10.

f.Follow heat value and specific gravity lines to point of intersection to find orifice size and manifold pressure settings for proper operation.

ON/OFF SWITCH

A99118

Fig. 48—Inducer Housing Drain Cap

INLET

PRESSURE TAP

REGULATOR

SEAL CAP

REGULATOR

ADJUSTMENT

SCREW

REGULATOR SPRING (PROPANE - WHITE, 6 TURNS NATURAL - SILVER, 10 TURNS)

GAS PRESSURE

REGULATOR

ADJUSTMENT

MANIFOLD

PRESSURE TAP

→

A03142

Fig. 50—Redundant Automatic Gas Valve

BURNER

ORIFICE

A93059

 

A99119

Fig. 49—Filling Condensate Trap

Fig. 51—Burner Orifice

 

1.Determine natural gas orifice size and manifold pressure for correct input.

a.Obtain average gas heat value (at installed altitude) from local gas supplier.

b.Obtain average gas specific gravity from local gas supplier.

—37—

CAUTION: DO NOT redrill orifices. Improper drilling (burrs, out-of-round holes, etc.) can cause excessive burner noise and misdirection of burner flames. This can result in flame impingement of burners and heat exchang- ers causing failures. (See Fig. 51.)

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Safety Considerations Electrostatic Discharge ESD PrecautionsMultipoise Orientations Unit Size DimensionsII. General Installation SafetyVI. GAS Piping and GAS Pipe Pressure Testing Codes and StandardsVII. Electrical Connections Electrostatic Discharge ESD PrecautionsApplications IntroductionGeneral II. Upflow ApplicationsCondensate Trap Tubing Factory-Shipped Orientation Pressure Switch TubingCondensate Trap Location Alternate Upflow Orientation Condensate Trap Tubing Alternate Upflow OrientationCondensate Trap Location III. Downflow ApplicationsCondensate Trap Tubing Horizontal Left Tube Configuration Construct a Working Platform IV. Horizontal Left SUPPLY-AIR Discharge ApplicationsHorizontal Right SUPPLY-AIR Discharge Applications Attic Location and Working Platform Location II. Furnace Location Relative to Cooling Equipment Furnace Location for Proper Condensate DrainageInstallation Leveling Legs if Desired II. Installation in Upflow or Downflow ApplicationsIII. Installation in Horizontal Applications III. Hazardous LocationsFurnace Plenum Opening Floor Opening Casing Opening DimensionsWidth II. Ductwork Acoustical Treatment Duct FlangesIV. Return AIR Connections III. Supply AIR ConnectionsFilter Arrangement Filter InformationVII. GAS Piping VI. Bottom Closure PanelMaximum Capacity of Pipe Casings onlyElectrical Connections Fire or Explosion HazardIII Accessories WiringPCB Direct Venting Electrical DataRemoval of Existing Furnaces from Common Vent Systems II. COMBUSTION-AIR and Vent PipingControl Center Clearance FT COMBUSTION-AIR and Vent Pipe Termination ClearancesExample Combustion-Air and Vent Pipe DiameterCombustion-Air and Vent Pipe Attachment Short Vent 5 to 8 Ft System COMBUSTION-AIR Intake Housing Plug FittingAltitude FT Maximum Allowable Pipe Length FT6001 to 7000‡ Air Intake Housing Plug Fitting Drain Extended Exposed Sidewall Pipes Vent Extension PipeTwo-Pipe Termination Kit IV. Multiventing and Vent Terminations Concentric Vent/Air Termination KitRoof Termination Preferred Sidewall Termination of 12 in. or Less II. Application Condensate Drain GeneralIII. Condensate Drain Protection II. Cooling Mode Heating ModeIII. Continuous Blower Mode IV. Heat Pump ModeIV. Adjustments START-UP Procedures GeneralComponent Test II. Prime Condensate Trap with WaterInducer Housing Drain Cap BTU/CU FT Orifice Manifold 625 650 Only 7001 675 725 8000 775 750 15% 825 2001to 725 750 Only 4001 775 800 825 5000 875 850 900 925 Altitude Derate Multiplier Example 100,000 Btuh Input Furnace Installed AT 4300 FTUnited States CanadaCheck Safety Controls Blower OFF Delay Setup PositionGAS Rate CU FT/HR Speed SelectorChecklist II. Check Pressure SwitchCheck Primary Limit Control CHECKLIST-START-UP CHECKLIST-INSTALLATIONLoad Calculation Combustion AIR Vent Piping
Related manuals
Manual 12 pages 2.16 Kb Manual 44 pages 12.97 Kb

340MAV specifications

The Bryant 340MAV is a standout model in the Bryant lineup, designed to provide exceptional comfort, efficiency, and performance for residential heating and cooling needs. This unit offers a perfect blend of innovative technology and user-friendly features, making it an ideal choice for homeowners seeking reliability and quality.

One of the defining characteristics of the Bryant 340MAV is its impressive efficiency rating. With a SEER (Seasonal Energy Efficiency Ratio) of up to 18, this model ensures that homeowners can enjoy effective cooling during the summer months while minimizing energy consumption. Similarly, the heating efficiency is notable, with a high AFUE (Annual Fuel Utilization Efficiency) rating. This makes the 340MAV an environmentally friendly option that also promotes cost savings on energy bills.

The 340MAV incorporates advanced technologies that enhance its performance. One such technology is the variable-speed compressor, which allows the system to adjust its output based on the demands of the home. This means that the unit operates more quietly and reduces energy usage by matching the cooling or heating output required. Additionally, the two-stage heating capability provides more consistent temperatures and improved comfort throughout the space.

Operating noise is a crucial factor in residential HVAC systems, and the Bryant 340MAV is designed with this in mind. Engineered for quiet operation, the unit features a sound-dampening design, including an insulated cabinet and a specially designed compressor that minimizes noise levels. Homeowners can enjoy a comfortable indoor climate without the disruptive racket often associated with traditional systems.

Furthermore, the Bryant 340MAV is equipped with a durable all-aluminum coil, which improves heat transfer efficiency while also being resistant to corrosion. This characteristic contributes to the longevity of the unit, ensuring that it can withstand various environmental factors without compromising performance.

Another key feature is the advanced control options that the Bryant 340MAV offers. Integration with smart thermostats allows homeowners to monitor and adjust their HVAC system remotely, ensuring optimal comfort at all times. Additionally, the system is compatible with Bryant's Perfect Air™ filtration system, enhancing indoor air quality by reducing pollutants and allergens.

In summary, the Bryant 340MAV is a high-efficiency heating and cooling solution that brings together cutting-edge technology, quiet operation, and user-friendly features. With its focus on comfort and energy savings, it stands out as a prime choice for homeowners looking to invest in a reliable HVAC system.
Top Page Image Contents