Bard FH085D36F, FLR140D60F, FLR110D48F, FLR085D36F, FH110D60F Typical Unit Setup FLF Unit Shown

Page 10

FIGURE 4

TYPICAL UNIT SETUP

FLF UNIT SHOWN

WARNING

ALL WIRING MUST

CONFORM TO THE ! NATIONAL ELECTRIC

CODE AND ALL LOCAL

CODES.

Left side high voltage (unit power) entrance

Left side low voltage (thermostat) entrance

Left side oil line entrance for opt. air boot

Left side oil line entrance

Oil line (see burner pump inst. for hookup info.)

Air Boot knockout (optional)

Control panel (junction box in FH units)

Right side high voltage (unit power) entrance

TYPICAL UNIT

SETUP

(FLF UNIT SHOWN)

Inspection door

Right side low voltage (thermostat) entrance

To thermostat and optional A/C unit

To power source

Shut off switch (if not fused, power line must include fuse or circuit breaker)

Power Wires:

Black (HOT) White (NEUTRAL)

Green (GROUND)

Right side

oil lineMIS-1836

entrance

Manual	2100-422M
Page	10 of 42

Image 10

Contents OIL Furnace Installation Instructions Contents Getting Other Information and Publications For More INFORMATION, Contact These PublishersLocating the Furnace Equipment SelectionMinimum Clearances FLF/FLR 085, 110 and 140 Specification Sheet Supply Specification Sheet Counterflow Specification Sheet FC085 Model DimensionsInstruments Required for Proper Setup of the Furnace Installing the FurnaceInstalling a Cooling Unit InstallationField Wiring WiringFactory Wiring Electrical DataTypical Unit Setup FLF Unit Shown Typical Unit Setup FLF Unit ShownI m n e y OIL Line Piping Typical Single Inside Tank InstallationBeckett AFG or NX OIL Burner Beckett Solid State Igniter Beckett Cleancut OIL PumpGenisys 7505 Primary Control Beckett Genisys Reset Button OperationBurner States Table a Reset Button Operation Table B Status LightsCAD Cell Resistance Indicator Priming the PumpResetting from Restricted Lockout Disable FunctionCleaner Connection Electronic Blower ControlBurner Setup and Adjustment Procedures Furnace DataPreparation Steps Combustion Adjustment StepsCombustion Diagnosis Short Form Adjustment Procedure High Air Settings Low Bacharach Smoke Number Typical Smoke CO2 Chart with Adjustment RangePressure Gauge Connection to Bleed Port Recommended START-UP Settings No Fuel OIL Efficiency Chart NET Stack TEMP. Degrees FCorrelation of Percent of CO2, O2 and Reserve AIR Combustion AIR Requirements GUN Assembly AdjustmentRemoving GUN Assembly Spacing of ElectrodesAFG Burner Combustion AIR Boot Assembly Combustion AIR Boot AssemblyAppliances Located in Confined Spaces ALL AIR from Inside BuildingALL Ventilation AIR from Outdoors Minimum Ventilation OpeningsAppliances Located in Confined Spaces ALL AIR from Outdoors Manual 2100-422M Thermostat Louvers and GrillesVenting Options Vertical VentingAFG Typical Installation of FR25 Filter KIT AIR FiltersFilter Installation LO-BOY Models LO-BOY Models Filter LocationsInspect AIR Filter Service HintsLubrication Final Inspection and TestCombination Combustion CHAMBER/BURNER Mounting System Removal of Burner onlyTo Remove the Entire Combustion Chamber Mounting System To Remove Burner onlyRemoval of Entire Combustion Chamber Mounting System Common Causes of Trouble Cleaning of the Heat ExchangerCare of Finish Chart FH110D60F Data Chart FH085D36F DataChart FH110D48F Data Chart FLF/FLR085D36F DataChart FLR140D60F Data Chart FC085D36F DataFH Series Wiring Diagram Exchanger4047-119 E 4047-120 D