Bard FC085D36F, FLR140D60F, FLR110D48F, FH110D60F Factory Wiring, Field Wiring, Electrical Data

Page 9

WIRING

FACTORY WIRING

All units are fully factory wired. Multispeed blowers are factory wired on high speed for cooling/manual fan operation. Heating speeds are wired for the largest input and may need lower speed for field installed low input nozzle. If replacement wire is necessary, use 105 degrees C minimum. See electrical data, Table 3.

FIELD WIRING

All wiring must conform to the National Electrical Code and all local codes. A separate fuse or breaker should be used for the furnace.

TABLE 3

ELECTRICAL DATA

									Max. Time
				Blower Motor		Burner Motor		Minimum	Delay Fuse
								Minimum	Delay Fuse
			Total	HP	FLA	HP	FLA	Circuit	or HACR
	Model	Volts-HZ-PH	Amps	HP	FLA	HP	FLA	Ampacity	Circuit Breaker
	Model	Volts-HZ-PH	Amps					Ampacity	Circuit Breaker

	FH085D36F	115-60-1	7.3	1/3	5.6	1/7	1.7	9	15

	FH110D48F	115-60-1	12.2	1/2	10.5	1/7	1.7	15	20

	FH110D60F	115-60-1	14.2	3/4	12.5	1/7	1.7	18	20

	FLF085D36F	115-60-1	7.3	1/3	5.6	1/7	1.7	9	15

	FLR085D36F	115-60-1	7.3	1/3	5.6	1/7	1.7	9	15

	FLF110D48F	115-60-1	12.2	1/2	10.5	1/7	1.7	15	20

	FLR110D48F	115-60-1	12.2	1/2	10.5	1/7	1.7	15	20

	FLF110D60F	115-60-1	14.2	3/4	12.5	1/7	1.7	18	20

	FLR110D60F	115-60-1	14.2	3/4	12.5	1/7	1.7	18	20

	FLR140D60F	115-60-1	14.2	3/4	12.5	1/7	1.7	18	20

	FC085D36F	115-60-1	7.3	1/3	5.6	1/7	1.7	9	15

Manual	2100-422M
Page	9 of 42

Image 9

Contents OIL Furnace Installation Instructions Contents For More INFORMATION, Contact These Publishers Getting Other Information and PublicationsEquipment Selection Locating the FurnaceMinimum Clearances FLF/FLR 085, 110 and 140 Specification Sheet Supply Specification Sheet FC085 Model Dimensions Counterflow Specification SheetInstalling a Cooling Unit Installing the FurnaceInstruments Required for Proper Setup of the Furnace InstallationFactory Wiring WiringField Wiring Electrical DataTypical Unit Setup FLF Unit Shown Typical Unit Setup FLF Unit ShownI m n e y Typical Single Inside Tank Installation OIL Line PipingBeckett AFG or NX OIL Burner Beckett Cleancut OIL Pump Beckett Solid State IgniterGenisys 7505 Primary Control Reset Button Operation Beckett GenisysBurner States Table B Status Lights Table a Reset Button OperationPriming the Pump CAD Cell Resistance IndicatorDisable Function Resetting from Restricted LockoutElectronic Blower Control Cleaner ConnectionFurnace Data Burner Setup and Adjustment ProceduresCombustion Adjustment Steps Preparation StepsCombustion Diagnosis Short Form Adjustment Procedure Typical Smoke CO2 Chart with Adjustment Range High Air Settings Low Bacharach Smoke NumberPressure Gauge Connection to Bleed Port No Fuel OIL Efficiency Chart NET Stack TEMP. Degrees F Recommended START-UP SettingsCorrelation of Percent of CO2, O2 and Reserve AIR Removing GUN Assembly GUN Assembly AdjustmentCombustion AIR Requirements Spacing of ElectrodesCombustion AIR Boot Assembly AFG Burner Combustion AIR Boot AssemblyALL AIR from Inside Building Appliances Located in Confined SpacesMinimum Ventilation Openings ALL Ventilation AIR from OutdoorsAppliances Located in Confined Spaces ALL AIR from Outdoors Manual 2100-422M Venting Options Louvers and GrillesThermostat Vertical VentingAFG AIR Filters Typical Installation of FR25 Filter KITLO-BOY Models Filter Locations Filter Installation LO-BOY ModelsLubrication Service HintsInspect AIR Filter Final Inspection and TestRemoval of Burner only Combination Combustion CHAMBER/BURNER Mounting SystemTo Remove Burner only To Remove the Entire Combustion Chamber Mounting SystemRemoval of Entire Combustion Chamber Mounting System Cleaning of the Heat Exchanger Common Causes of TroubleCare of Finish Chart FH110D48F Data Chart FH085D36F DataChart FH110D60F Data Chart FLF/FLR085D36F DataChart FC085D36F Data Chart FLR140D60F DataExchanger FH Series Wiring Diagram4047-119 E 4047-120 D