Bard FLR140D60F, FLR110D48F LO-BOY Models Filter Locations, Filter Installation LO-BOY Models

Page 33

LO-BOY MODELS – FILTER LOCATIONS

Lo-boy models have the filter installed in the return air cabinet section of the furnace. It is accessible from the rear of the furnace by removing the blower/filter access door. The electrical switch should be turned “off” prior to removing the access door. Refer to Figure 18 below.

 

FIGURE 18

 

FILTER INSTALLATION – LO-BOY MODELS

UNIT

FILTER SIZE

FLF/FLR085

16 x 20 x 2

FLF/FLR110

20 x 20 x 2

FLR140

20 x 25 x 2

STEP 3:

SLIDE FILTER OUT

TOWARDS BLOWER

DOOR

STEP 2:

REMOVE BLOWER DOOR

STEP 1:

UNFASTEN SWELL

BY PULLING OUT ON

LATCHES BY PULLING

SWELL LATCHES AND

HANDLES OUTWARD

TILTING OUTWARDS

 

MIS-1835 A

Manual

2100-422M

Page

33 of 42

Page 32 Page 34
Image 33
Page 32 Page 34
Contents OIL Furnace Installation Instructions Contents For More INFORMATION, Contact These Publishers Getting Other Information and PublicationsEquipment Selection Locating the FurnaceMinimum Clearances FLF/FLR 085, 110 and 140 Specification Sheet Supply Specification Sheet FC085 Model Dimensions Counterflow Specification SheetInstalling a Cooling Unit Installing the FurnaceInstruments Required for Proper Setup of the Furnace InstallationFactory Wiring WiringField Wiring Electrical DataTypical Unit Setup FLF Unit Shown Typical Unit Setup FLF Unit ShownI m n e y Typical Single Inside Tank Installation OIL Line PipingBeckett AFG or NX OIL Burner Beckett Cleancut OIL Pump Beckett Solid State IgniterGenisys 7505 Primary Control Reset Button Operation Beckett GenisysBurner States Table B Status Lights Table a Reset Button OperationPriming the Pump CAD Cell Resistance IndicatorDisable Function Resetting from Restricted LockoutElectronic Blower Control Cleaner ConnectionFurnace Data Burner Setup and Adjustment ProceduresCombustion Adjustment Steps Preparation StepsCombustion Diagnosis Short Form Adjustment Procedure Typical Smoke CO2 Chart with Adjustment Range High Air Settings Low Bacharach Smoke NumberPressure Gauge Connection to Bleed Port No Fuel OIL Efficiency Chart NET Stack TEMP. Degrees F Recommended START-UP SettingsCorrelation of Percent of CO2, O2 and Reserve AIR Removing GUN Assembly GUN Assembly AdjustmentCombustion AIR Requirements Spacing of ElectrodesCombustion AIR Boot Assembly AFG Burner Combustion AIR Boot AssemblyALL AIR from Inside Building Appliances Located in Confined SpacesMinimum Ventilation Openings ALL Ventilation AIR from OutdoorsAppliances Located in Confined Spaces ALL AIR from Outdoors Manual 2100-422M Venting Options Louvers and GrillesThermostat Vertical VentingAFG AIR Filters Typical Installation of FR25 Filter KITLO-BOY Models Filter Locations Filter Installation LO-BOY ModelsLubrication Service HintsInspect AIR Filter Final Inspection and TestRemoval of Burner only Combination Combustion CHAMBER/BURNER Mounting SystemTo Remove Burner only To Remove the Entire Combustion Chamber Mounting SystemRemoval of Entire Combustion Chamber Mounting System Cleaning of the Heat Exchanger Common Causes of TroubleCare of Finish Chart FH110D48F Data Chart FH085D36F DataChart FH110D60F Data Chart FLF/FLR085D36F DataChart FC085D36F Data Chart FLR140D60F DataExchanger FH Series Wiring Diagram4047-119 E 4047-120 D
Top Page Image Contents