Linear DUAL 824 manual Programming Different Sensor Types

Page 18

PROGRAMMING DIFFERENT SENSOR TYPES

✦Follow the instructions on the previous page to select a sensor number to program the sensor into.

✎NOTE: A sensor can be programmed into more than one location. Be sure to choose an UNUSED sensor number. If a sensor gets entered into more than one location, delete the duplicates using the remove sensor function.

✦To add DXS-10 wireless keypads, press and hold the keypad's key until programmed into the Control Panel.

✦For DXS-31 and DXS-32 door/window sensors, move the magnet away from the side of the sensor.

✎IMPORTANT NOTE: The DXS-31 & DXS-32 door/ window sensors are pre-set at the factory for delayed burglary response. If the sensor is going to be used on a non-entry portal (window, sliding glass door, etc.) a jumper can be changed in the sensor to select instant response. The jumper should be changed before programming the sensor so the Control Panel will assign the sensor to the proper sensor function. See the “Basic Sensor Installation” section of this manual or the sensor’s instructions for details on changing the jumper.

✦For DXS-81, DXS-91, DXS-54, DXS-73, & accessory sensors, simply send a test transmission (refer to the sensor's instructions for details on sending a test transmission).

DXS-10

DXS-32

DXS-81

16

Image 18

Contents Supervised Wireless Security Control Panel Introduction Linear LLCTable of Contents Dual 824 Security System Control PanelDOOR/WINDOW Sensors Wireless KeypadRemote Controls Panic ButtonsDesign the Installation Security System Floor PlanExample System Five system mode indicators Hardwired KeypadThree system supervisory indicators Overview of KeypadsHardwired Keypad Features Control Panel Features Terminals for hardwired loop inputsWall Mounting Control Panel InstallationSystem Location External AntennaHardwired Keypad Installation Hardwired Loop Wiring ARM/DISARM KEY Station WiringExternal Alarm Siren Connection Telephone Line ConnectionAutomation Output Connection Voice Response ModuleControl Panel Power Connection Backup Battery InstallationBasic Control Panel Programming Create the Master User CodeGong and four beeps will sound Program the Hardwired Loops Repeat Steps 3-6 to enable all of the hardwired loops usedProgram the Wireless Sensors Programming Different Sensor Types For All Models Basic Sensor Installation DXS-10 Wireless KeypadDXS-31 & DXS-32 DOOR/WINDOW Sensors Test SensorsCustomizing the Keypad Labeling the Sensor LocationsOFF Mode Chime ModeSystem Operating Modes Home Instant Mode Home ModeLit sensor status indicators show which sensors are open Manual Bypassing of SensorsAway Mode Exit Delay For Leaving the PremisesTest Mode Sensor Operation in Each System ModeSensor Function Table Wireless Sensor LOW Batteries Control Panel PowerPower indicator normally glows when AC power is on System Trouble IndicationsGong and ﬁ ve Beeps will sound Customizing the SystemAdding Sensors to the System Removing Sensors from the SystemMaking a Sensor Interior Making a Sensor a 24-HOUR Door ChimePress HOME, 8, then Away Press HOME, 7, then AwayProgramming Information Sensor Operation in Each System Mode Making a Sensor Perform a Different FunctionSetup Mode Advanced ProgrammingControl Panel Programming Options Exit Delay Time Changing a Sensors Restore RequirementsEntry Delay Time Changing a Sensors SupervisionEntry Delay Beeps Remote Control & Hardwire Arming LevelRemote Control & Hardwire Disarming Level Exit Delay BeepsDisabling Quick Arming Silent Burglary AlarmsSilent Emergency Alarms Automatic Restoral of Bypassed SensorsAutomation Output on During and After Alarm Automation Output Mode During AlarmRemote Control & Hardwire ARM/DISARM Chirp Automation Output on During AlarmAutomation Output While Armed Automation Output During EXIT/ENTRY DelaysRemote Access Password Automation Output PolarityControl Panel Master Reset Adding Additional User CodesRemoving Additional User Codes Communicator Programming General Communicator OptionsWAY Audio Communicator EnableWay manual, 3 2-way full duplex using this step Voice ResponseDialing Delay Call LimiterDialing Method Reporting Format Call RoutingPrimary Telephone Number Telephone Number Delays and Special CharactersAccount Number Secondary Telephone NumberOpening and Closing Reports Report Control Panel TroubleReport Force Arming Point ID ReportingGeneral Reporting Codes Steps #201-206Steps #261-266 System Reporting CodesFire and Emergency buttons and for each Force Arming Reporting CodeBy 2 Format Point ID Trouble Report Codes By 2 Format Point ID Alarm Report CodesSteps #210-233 Steps #234-257By 2 Format Point ID Reporting Codes Important Information