Linear DUAL 824 manual Call Limiter, Dialing Delay, Dialing Method

Page 40

CALL LIMITER

✦The factory setting for the call limiter is OFF. This allows the communicator to report burglary alarms, once for each sensor, as many times as they are triggered.

STEP #101 The Control Panel can be programmed to only allow ﬁve burglary reports total per arming period using this step.

✎NOTE: Sensors programmed for 24-hour functions (Emergency, Panic, Fire) always send a Central Station report and always sound the local siren regardless of the Call Limiter setting.

PROGRAMMING STEP #101

ENTERS STEP NUMBER

0 FOR OFF (UNLIMITED)

1 FOR ON (5 VIOLATIONS)

STORES VALUE - 1 BING

DIALING DELAY

✦The factory setting will cause the communicator to dial the Central Station instantly when an alarm or supervisory event occurs.

STEP #103 The communicator can be programmed to wait 30 seconds before dialing using this step. This gives the user time to disarm the system and prevent communications in the case of a subscriber generated false alarm.

PROGRAMMING STEP #103

ENTERS STEP NUMBER

0 FOR NO DELAY

1 FOR 30 SECOND DELAY

STORES VALUE - 1 BING

DIALING METHOD

✦The factory setting causes the communicator to dial using DTMF (dual-tone multi-frequency) tone dialing.

STEP #104 The communicator can be programmed to use pulse (rotary) dialing using this step. Use this option if the telephone line in the installation does not support tone dialing.

PROGRAMMING STEP #104

ENTERS STEP NUMBER

0 FOR TONE DIALING

1 FOR PULSE DIALING

STORES VALUE - 1 BING

38

Image 40

Contents Supervised Wireless Security Control Panel Introduction Linear LLCTable of Contents Dual 824 Security System Control PanelWireless Keypad Remote ControlsDOOR/WINDOW Sensors Panic ButtonsSecurity System Floor Plan Design the InstallationExample System Hardwired Keypad Three system supervisory indicatorsFive system mode indicators Overview of KeypadsHardwired Keypad Features Control Panel Features Terminals for hardwired loop inputsControl Panel Installation System LocationWall Mounting External AntennaHardwired Keypad Installation Hardwired Loop Wiring ARM/DISARM KEY Station WiringExternal Alarm Siren Connection Telephone Line ConnectionAutomation Output Connection Voice Response ModuleControl Panel Power Connection Backup Battery InstallationCreate the Master User Code Basic Control Panel ProgrammingGong and four beeps will sound Repeat Steps 3-6 to enable all of the hardwired loops used Program the Hardwired LoopsProgram the Wireless Sensors Programming Different Sensor Types For All Models Basic Sensor Installation DXS-10 Wireless KeypadDXS-31 & DXS-32 DOOR/WINDOW Sensors Test SensorsCustomizing the Keypad Labeling the Sensor LocationsChime Mode OFF ModeSystem Operating Modes Home Mode Lit sensor status indicators show which sensors are openHome Instant Mode Manual Bypassing of SensorsAway Mode Exit Delay For Leaving the PremisesSensor Operation in Each System Mode Test ModeSensor Function Table Control Panel Power Power indicator normally glows when AC power is onWireless Sensor LOW Batteries System Trouble IndicationsCustomizing the System Adding Sensors to the SystemGong and ﬁ ve Beeps will sound Removing Sensors from the SystemMaking a Sensor a 24-HOUR Door Chime Press HOME, 8, then AwayMaking a Sensor Interior Press HOME, 7, then AwayProgramming Information Sensor Operation in Each System Mode Making a Sensor Perform a Different FunctionAdvanced Programming Setup ModeControl Panel Programming Options Changing a Sensors Restore Requirements Entry Delay TimeExit Delay Time Changing a Sensors SupervisionRemote Control & Hardwire Arming Level Remote Control & Hardwire Disarming LevelEntry Delay Beeps Exit Delay BeepsSilent Burglary Alarms Silent Emergency AlarmsDisabling Quick Arming Automatic Restoral of Bypassed SensorsAutomation Output Mode During Alarm Remote Control & Hardwire ARM/DISARM ChirpAutomation Output on During and After Alarm Automation Output on During AlarmAutomation Output During EXIT/ENTRY Delays Remote Access PasswordAutomation Output While Armed Automation Output PolarityAdding Additional User Codes Control Panel Master ResetRemoving Additional User Codes Communicator Programming General Communicator OptionsCommunicator Enable Way manual, 3 2-way full duplex using this stepWAY Audio Voice ResponseCall Limiter Dialing DelayDialing Method Reporting Format Call RoutingTelephone Number Delays and Special Characters Account NumberPrimary Telephone Number Secondary Telephone NumberReport Control Panel Trouble Report Force ArmingOpening and Closing Reports Point ID ReportingGeneral Reporting Codes Steps #201-206System Reporting Codes Fire and Emergency buttons and for eachSteps #261-266 Force Arming Reporting CodeBy 2 Format Point ID Alarm Report Codes Steps #210-233By 2 Format Point ID Trouble Report Codes Steps #234-257By 2 Format Point ID Reporting Codes Important Information