Linear DUAL 824 Fire Siren Time, Automation Output Time, Remote Control & Hardwire Arming Level

Page 33

FIRE SIREN TIME

✦The factory-set fire siren time is five minutes (UL installation maximum).

STEP #32 The fire siren time can be adjusted from one to 30 minutes using this step.

PROGRAMMING STEP #32

ENTERS STEP NUMBER

TIME IN MINUTES 1 - 30

STORES VALUE - 1 BING

AUTOMATION OUTPUT TIME

✦The factory setting causes the Automation Output to toggle between on and off with each activation.

STEP #40 The Automation Output can be programmed to turn on, then automatically turn off after one to 2500 seconds (42 minutes), or toggle on & off, using this step.

PROGRAMMING STEP #40

ENTERS STEP NUMBER

TIME IN SECONDS 1 - 2500 0 = TOGGLE ON & OFF

STORES VALUE - 1 BING

REMOTE CONTROL & HARDWIRE ARMING LEVEL

✦The factory setting causes the portable remote controls to arm to the Away Mode.

STEP #50 The portable remote controls can be changed to

arm to the Home Mode using this step.

✎NOTE: Changing this setting will affect all the portable remote controls used with the system and all hardwired loops programmed as arm/disarm (sensor Function #9) key stations.

PROGRAMMING STEP #50

ENTERS STEP NUMBER

2 FOR HOME MODE

3 FOR AWAY MODE

STORES VALUE - 1 BING

REMOTE CONTROL & HARDWIRE DISARMING LEVEL

✦The factory setting causes the portable remote controls to disarm to the Off Mode.

STEP #51 The remote controls can be changed to disarm to the Chime Mode using this step.

✎NOTE: Changing this setting will affect all the portable remote controls used with the system and all hardwired loops programmed as arm/disarm (sensor Function #9) key stations.

PROGRAMMING STEP #51

ENTERS STEP NUMBER

0 FOR OFF MODE

1 FOR CHIME MODE

STORES VALUE - 1 BING

ENTRY DELAY BEEPS

✦The factory setting causes the keypad(s) to beep during Entry Delays.

STEP #61 The Entry Delay beeps can be silenced using this step.

✦With the Entry Delay beeps off, the keypad(s) will be silent after a delayed sensor is triggered until the Entry Delay expires, then the alarm siren will sound.

PROGRAMMING STEP #61

ENTERS STEP NUMBER

0 FOR ENTRY BEEPS OFF

1 FOR ENTRY BEEPS ON

STORES VALUE - 1 BING

EXIT DELAY BEEPS

✦The factory setting causes the keypad(s) to beep during Exit Delays.

STEP #62 The Exit Delay beeps can be silenced using this step.

✦With the Exit Delay beeps off, the keypad(s) will be silent after arming to the Away Mode until the Exit Delay expires, then a single “Gong” tone will sound.

PROGRAMMING STEP #62

ENTERS STEP NUMBER

0 FOR EXIT BEEPS OFF

1 FOR EXIT BEEPS ON

STORES VALUE - 1 BING

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Supervised Wireless Security Control Panel Linear LLC IntroductionTable of Contents Control Panel Dual 824 Security SystemRemote Controls Wireless KeypadDOOR/WINDOW Sensors Panic ButtonsDesign the Installation Security System Floor PlanExample System Three system supervisory indicators Hardwired KeypadFive system mode indicators Overview of KeypadsHardwired Keypad Features Terminals for hardwired loop inputs Control Panel FeaturesSystem Location Control Panel InstallationWall Mounting External AntennaHardwired Keypad Installation ARM/DISARM KEY Station Wiring Hardwired Loop WiringTelephone Line Connection External Alarm Siren ConnectionVoice Response Module Automation Output ConnectionBackup Battery Installation Control Panel Power ConnectionBasic Control Panel Programming Create the Master User CodeGong and four beeps will sound Program the Hardwired Loops Repeat Steps 3-6 to enable all of the hardwired loops usedProgram the Wireless Sensors Programming Different Sensor Types For All Models DXS-10 Wireless Keypad Basic Sensor InstallationTest Sensors DXS-31 & DXS-32 DOOR/WINDOW SensorsLabeling the Sensor Locations Customizing the KeypadOFF Mode Chime ModeSystem Operating Modes Lit sensor status indicators show which sensors are open Home ModeHome Instant Mode Manual Bypassing of SensorsExit Delay For Leaving the Premises Away ModeTest Mode Sensor Operation in Each System ModeSensor Function Table Power indicator normally glows when AC power is on Control Panel PowerWireless Sensor LOW Batteries System Trouble IndicationsAdding Sensors to the System Customizing the SystemGong and fi ve Beeps will sound Removing Sensors from the SystemPress HOME, 8, then Away Making a Sensor a 24-HOUR Door ChimeMaking a Sensor Interior Press HOME, 7, then AwayMaking a Sensor Perform a Different Function Programming Information Sensor Operation in Each System ModeSetup Mode Advanced ProgrammingControl Panel Programming Options Entry Delay Time Changing a Sensors Restore RequirementsExit Delay Time Changing a Sensors SupervisionRemote Control & Hardwire Disarming Level Remote Control & Hardwire Arming LevelEntry Delay Beeps Exit Delay BeepsSilent Emergency Alarms Silent Burglary AlarmsDisabling Quick Arming Automatic Restoral of Bypassed SensorsRemote Control & Hardwire ARM/DISARM Chirp Automation Output Mode During AlarmAutomation Output on During and After Alarm Automation Output on During AlarmRemote Access Password Automation Output During EXIT/ENTRY DelaysAutomation Output While Armed Automation Output PolarityControl Panel Master Reset Adding Additional User CodesRemoving Additional User Codes General Communicator Options Communicator ProgrammingWay manual, 3 2-way full duplex using this step Communicator EnableWAY Audio Voice ResponseDialing Delay Call LimiterDialing Method Call Routing Reporting FormatAccount Number Telephone Number Delays and Special CharactersPrimary Telephone Number Secondary Telephone NumberReport Force Arming Report Control Panel TroubleOpening and Closing Reports Point ID ReportingSteps #201-206 General Reporting CodesFire and Emergency buttons and for each System Reporting CodesSteps #261-266 Force Arming Reporting CodeSteps #210-233 By 2 Format Point ID Alarm Report CodesBy 2 Format Point ID Trouble Report Codes Steps #234-257By 2 Format Point ID Reporting Codes Important Information
Top Page Image Contents