Linear DUAL 824 manual System Operating Modes, OFF Mode, Chime Mode

Page 23

10. SYSTEM OPERATING MODES

OFF MODE

✦Use this mode to disarm the burglary portion of the system.

✦The 24-hour functions are still active in Off Mode and can be triggered with wireless or hardwired sensors, or by pressing the FIRE or EMERGENCY on the keypad(s).

1.Switch to Off Mode by entering the user code, and pressing OFF.

✎NOTE: The keypad'skey resets the keypad's keyboard and can be used before entering any

code to assure that any digits recently pressed will not be added to the correct code. Pressing ﬁrst is optional because the keypad will reset itself after 10 seconds of keyboard inactivity.

✴When the system is disarmed to Off Mode, the keypad(s) will sound one “Gong”.

✦Switching to Off Mode stops any alarms in progress.

✴If an alarm has occurred, multiple Beeps will sound after disarming and the sensor indicator for the sensor(s) that caused the alarm will ﬂ ash.

✎NOTE: In Off Mode, protected doors and windows cannot trigger the burglary alarm.

CHIME MODE

✦Chime Mode is for monitoring entries and exits without causing alarms.

✦Use Chime Mode as an “automatic door chime” when at home.

✴Opening any protected door or window causes the keypad(s) to sound a “ding-dong”.

1A. Select the Chime Mode by entering a user code, then press CHIME.

1B. The user can enter Chime Mode from Off Mode by pressing CHIME for two seconds.

✴When the system is switched to the Chime Mode, the keypad(s) will sound a “Gong” and one “Beep”.

✦Switching to Chime Mode disarms the system and stops any alarms in progress.

✴If an alarm has occurred, multiple Beeps will sound after disarming and the sensor indicator for the sensor(s) that caused the alarm will ﬂ ash.

✎NOTE: In Chime Mode, protected doors and windows cannot trigger the burglary alarm.

OFF MODE

START HERE

(OPTIONAL)

YOUR

USER

CODE

1 GONG

DONE

CHIME MODE

START HERE

(OPTIONAL)

YOUR

USER

CODE

1GONG & 1 BEEP

DONE

OR QUICK ARM TO CHIME MODE

START IN OFF

HOLD DOWN

1 GONG & 1 BEEP

DONE

21

Image 23

Contents Supervised Wireless Security Control Panel Linear LLC IntroductionTable of Contents Control Panel Dual 824 Security SystemPanic Buttons Wireless KeypadRemote Controls DOOR/WINDOW SensorsExample System Design the InstallationSecurity System Floor Plan Overview of Keypads Hardwired KeypadThree system supervisory indicators Five system mode indicatorsHardwired Keypad Features Terminals for hardwired loop inputs Control Panel FeaturesExternal Antenna Control Panel InstallationSystem Location Wall MountingHardwired Keypad Installation ARM/DISARM KEY Station Wiring Hardwired Loop WiringTelephone Line Connection External Alarm Siren ConnectionVoice Response Module Automation Output ConnectionBackup Battery Installation Control Panel Power ConnectionGong and four beeps will sound Basic Control Panel ProgrammingCreate the Master User Code Program the Wireless Sensors Program the Hardwired LoopsRepeat Steps 3-6 to enable all of the hardwired loops used Programming Different Sensor Types For All Models DXS-10 Wireless Keypad Basic Sensor InstallationTest Sensors DXS-31 & DXS-32 DOOR/WINDOW SensorsLabeling the Sensor Locations Customizing the KeypadSystem Operating Modes OFF ModeChime Mode Manual Bypassing of Sensors Home ModeLit sensor status indicators show which sensors are open Home Instant ModeExit Delay For Leaving the Premises Away ModeSensor Function Table Test ModeSensor Operation in Each System Mode System Trouble Indications Control Panel PowerPower indicator normally glows when AC power is on Wireless Sensor LOW BatteriesRemoving Sensors from the System Customizing the SystemAdding Sensors to the System Gong and ﬁ ve Beeps will soundPress HOME, 7, then Away Making a Sensor a 24-HOUR Door ChimePress HOME, 8, then Away Making a Sensor InteriorMaking a Sensor Perform a Different Function Programming Information Sensor Operation in Each System ModeControl Panel Programming Options Setup ModeAdvanced Programming Changing a Sensors Supervision Changing a Sensors Restore RequirementsEntry Delay Time Exit Delay TimeExit Delay Beeps Remote Control & Hardwire Arming LevelRemote Control & Hardwire Disarming Level Entry Delay BeepsAutomatic Restoral of Bypassed Sensors Silent Burglary AlarmsSilent Emergency Alarms Disabling Quick ArmingAutomation Output on During Alarm Automation Output Mode During AlarmRemote Control & Hardwire ARM/DISARM Chirp Automation Output on During and After AlarmAutomation Output Polarity Automation Output During EXIT/ENTRY DelaysRemote Access Password Automation Output While ArmedRemoving Additional User Codes Control Panel Master ResetAdding Additional User Codes General Communicator Options Communicator ProgrammingVoice Response Communicator EnableWay manual, 3 2-way full duplex using this step WAY AudioDialing Method Dialing DelayCall Limiter Call Routing Reporting FormatSecondary Telephone Number Telephone Number Delays and Special CharactersAccount Number Primary Telephone NumberPoint ID Reporting Report Control Panel TroubleReport Force Arming Opening and Closing ReportsSteps #201-206 General Reporting CodesForce Arming Reporting Code System Reporting CodesFire and Emergency buttons and for each Steps #261-266Steps #234-257 By 2 Format Point ID Alarm Report CodesSteps #210-233 By 2 Format Point ID Trouble Report CodesBy 2 Format Point ID Reporting Codes Important Information