Linear DUAL 824 manual By 2 Format Point ID Alarm Report Codes, Steps #210-233, Steps #234-257

Page 46

4 BY 2 FORMAT POINT ID REPORTING CODES

4 BY 2 FORMAT POINT ID ALARM REPORT CODES

✦Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the alarm reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled

and any sensor triggers an alarm. The factory settings are listed, along with a blank area to write in the new installation values.

✦Use program Steps #210 - 233 to change the 4 by 2 Point ID alarm reporting codes.

✎NOTE: Be careful not to duplicate codes unless the Central Station requires speciﬁc codes for certain types of sensors.

PROGRAMMING

STEPS #210 - 233

ENTERS STEP NUMBER

0 - 99 FOR SENSOR ALARM CODE

STORES VALUE - 1 BING

STEPS #210-233

Any value from 0-99 can be programmed for each event using these steps (enter “0” to stop an event from reporting).

4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES

✦Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the trouble reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled and any sensor has a low battery or trouble condition. The factory settings are listed, along with a blank area to write in the new installation values.

✦Use program Steps #234 - 257 to change the 4 by 2 Point ID trouble reporting codes.

✎NOTE: Be careful not to duplicate codes unless the Central Station requires speciﬁc codes for certain types of sensors.

PROGRAMMING

STEPS #234 - 257

ENTERS STEP NUMBER

0 - 99 FOR SENSOR TROUBLE CODE

STORES VALUE - 1 BING

STEPS #234-257

Any value from 0-99 can be programmed for each event using these steps (enter “0” to stop an event from reporting).

44

Image 46

Contents Supervised Wireless Security Control Panel Introduction Linear LLCTable of Contents Dual 824 Security System Control PanelDOOR/WINDOW Sensors Wireless KeypadRemote Controls Panic ButtonsSecurity System Floor Plan Design the InstallationExample System Five system mode indicators Hardwired KeypadThree system supervisory indicators Overview of KeypadsHardwired Keypad Features Control Panel Features Terminals for hardwired loop inputsWall Mounting Control Panel InstallationSystem Location External AntennaHardwired Keypad Installation Hardwired Loop Wiring ARM/DISARM KEY Station WiringExternal Alarm Siren Connection Telephone Line ConnectionAutomation Output Connection Voice Response ModuleControl Panel Power Connection Backup Battery InstallationCreate the Master User Code Basic Control Panel ProgrammingGong and four beeps will sound Repeat Steps 3-6 to enable all of the hardwired loops used Program the Hardwired LoopsProgram the Wireless Sensors Programming Different Sensor Types For All Models Basic Sensor Installation DXS-10 Wireless KeypadDXS-31 & DXS-32 DOOR/WINDOW Sensors Test SensorsCustomizing the Keypad Labeling the Sensor LocationsChime Mode OFF ModeSystem Operating Modes Home Instant Mode Home ModeLit sensor status indicators show which sensors are open Manual Bypassing of SensorsAway Mode Exit Delay For Leaving the PremisesSensor Operation in Each System Mode Test ModeSensor Function Table Wireless Sensor LOW Batteries Control Panel PowerPower indicator normally glows when AC power is on System Trouble IndicationsGong and ﬁ ve Beeps will sound Customizing the SystemAdding Sensors to the System Removing Sensors from the SystemMaking a Sensor Interior Making a Sensor a 24-HOUR Door ChimePress HOME, 8, then Away Press HOME, 7, then AwayProgramming Information Sensor Operation in Each System Mode Making a Sensor Perform a Different FunctionAdvanced Programming Setup ModeControl Panel Programming Options Exit Delay Time Changing a Sensors Restore RequirementsEntry Delay Time Changing a Sensors SupervisionEntry Delay Beeps Remote Control & Hardwire Arming LevelRemote Control & Hardwire Disarming Level Exit Delay BeepsDisabling Quick Arming Silent Burglary AlarmsSilent Emergency Alarms Automatic Restoral of Bypassed SensorsAutomation Output on During and After Alarm Automation Output Mode During AlarmRemote Control & Hardwire ARM/DISARM Chirp Automation Output on During AlarmAutomation Output While Armed Automation Output During EXIT/ENTRY DelaysRemote Access Password Automation Output PolarityAdding Additional User Codes Control Panel Master ResetRemoving Additional User Codes Communicator Programming General Communicator OptionsWAY Audio Communicator EnableWay manual, 3 2-way full duplex using this step Voice ResponseCall Limiter Dialing DelayDialing Method Reporting Format Call RoutingPrimary Telephone Number Telephone Number Delays and Special CharactersAccount Number Secondary Telephone NumberOpening and Closing Reports Report Control Panel TroubleReport Force Arming Point ID ReportingGeneral Reporting Codes Steps #201-206Steps #261-266 System Reporting CodesFire and Emergency buttons and for each Force Arming Reporting CodeBy 2 Format Point ID Trouble Report Codes By 2 Format Point ID Alarm Report CodesSteps #210-233 Steps #234-257By 2 Format Point ID Reporting Codes Important Information