Linear DUAL 824 manual Adding Additional User Codes, Removing Additional User Codes

Page 37

ADDING ADDITIONAL USER CODES

✦The Control Panel can be programmed with five restricted user codes and one page alert user code.

✦The restricted user codes operate the system as usual, but cannot access Setup Mode.

✦The restricted user codes can access a special Code Mode that can be used to change or remove any of the five restricted user codes, the page alert user code, or the duress code.

✦The page alert user code dials the supervisory number (programmed for a pager) when it is used to arm or disarm the system.

✦A restricted user code is appropriate to give any user that should be restricted from programming the Control Panel.

✎NOTE: For maximum security, a 3-5 digit code is recommended.

✎WARNING: NEVER PROGRAM ANY RESTRICTED USER CODETHE SAME ASTHE MASTER USER CODE!

PROGRAMMING STEP #93-98

ENTERS STEP NUMBER

1-5 DIGIT ADDITIONAL USER CODE

(3-5 DIGITS RECOMMENDED)

STORES CODE - 1 BING

STEP

CODE FUNCTION

CODE ENTERED

STEP #93

RESTRICTED USER CODE #1

 

 

 

 

STEP #94

RESTRICTED USER CODE #2

 

 

 

 

STEP #95

RESTRICTED USER CODE #3

 

 

 

 

STEP #96

RESTRICTED USER CODE #4

 

 

 

 

STEP #97

RESTRICTED USER CODE #5

 

 

 

 

STEP #98

PAGE ALERT USER CODE

 

 

 

 

STEPS #93-98Create any additional user codes using these steps then log the codes in the boxes to the right.

REMOVING ADDITIONAL USER CODES

STEPS #93-98Any additional user code can be removed

 

ENTER FOR STEP #

from the Control Panel by entering the

93 = RESTRICTED CODE 1

appropriate step number and pressing TEST.

94 = RESTRICTED CODE 2

✦ Because access to programming would be

95 = RESTRICTED CODE 3

96 = RESTRICTED CODE 4

impossible without a master user code, it cannot be

97 = RESTRICTED CODE 5

removed using these steps. The master user code

98 = PAGE ALERT USER CODE

can be changed using programming STEP #99.

 

✎ NOTE: The master user code can be set to the

PROGRAMMING STEP #93-98

factory default using the Control Panel master

 

reset programming step, although all other system

 

programming will be reset to factory values and all

REMOVES CODE - 1 BING

sensors programmed will be erased.

 

CONTROL PANEL MASTER RESET

✦Master resetting the Control Panel will set all of the programming options back to the factory values. The master user code will be reset to 1234.

✎CAUTION: Master resetting the Control Panel will erase the user codes and remove all programmed sensors. All Control Panel and communicator programming values will be reset to the factory defaults.

1.Start with the system in Test Mode (Setup Mode cannot be reached from any other mode).

2.From Test Mode, enter the master user code then press TEST.

✴A “Gong” and fi ve “Beeps” will sound, signaling that the system is in Setup Mode.

3.Enter programming STEP #999 then press TEST.

4.Enter 999 again then press TEST again.

✴A “Bing” will sound to indicate the beginning of the reset process. This process will take up to 10 seconds while the memory is being reset.

✦The system will revert to the first time power- up condition and the new master user code will be 1234. Go to the “Basic Control Panel Programming” section of this manual to begin re- programming the system.

START IN TEST

MASTER USER CODE

ENTERS TEST MODE 1 GONG & 5 BEEPS

STEP #999

FOR MASTER

RESET

ENTERS STEP NUMBER

ENTER 999 TO OK

THE MASTER RESET

PRESS TEST, 1 BING SOUNDS,

WAIT ABOUT 10 SECONDS

DONE

USE THESE EXACT KEYSTROKES

TO PERFORM A MASTER RESET

35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Supervised Wireless Security Control Panel Linear LLC IntroductionTable of Contents Control Panel Dual 824 Security SystemRemote Controls Wireless KeypadDOOR/WINDOW Sensors Panic ButtonsSecurity System Floor Plan Design the InstallationExample System Three system supervisory indicators Hardwired KeypadFive system mode indicators Overview of KeypadsHardwired Keypad Features Terminals for hardwired loop inputs Control Panel FeaturesSystem Location Control Panel InstallationWall Mounting External AntennaHardwired Keypad Installation ARM/DISARM KEY Station Wiring Hardwired Loop WiringTelephone Line Connection External Alarm Siren ConnectionVoice Response Module Automation Output ConnectionBackup Battery Installation Control Panel Power ConnectionCreate the Master User Code Basic Control Panel ProgrammingGong and four beeps will sound Repeat Steps 3-6 to enable all of the hardwired loops used Program the Hardwired LoopsProgram the Wireless Sensors Programming Different Sensor Types For All Models DXS-10 Wireless Keypad Basic Sensor InstallationTest Sensors DXS-31 & DXS-32 DOOR/WINDOW SensorsLabeling the Sensor Locations Customizing the KeypadChime Mode OFF ModeSystem Operating Modes Lit sensor status indicators show which sensors are open Home ModeHome Instant Mode Manual Bypassing of SensorsExit Delay For Leaving the Premises Away ModeSensor Operation in Each System Mode Test ModeSensor Function Table Power indicator normally glows when AC power is on Control Panel PowerWireless Sensor LOW Batteries System Trouble IndicationsAdding Sensors to the System Customizing the SystemGong and fi ve Beeps will sound Removing Sensors from the SystemPress HOME, 8, then Away Making a Sensor a 24-HOUR Door ChimeMaking a Sensor Interior Press HOME, 7, then AwayMaking a Sensor Perform a Different Function Programming Information Sensor Operation in Each System ModeAdvanced Programming Setup ModeControl Panel Programming Options Entry Delay Time Changing a Sensors Restore RequirementsExit Delay Time Changing a Sensors SupervisionRemote Control & Hardwire Disarming Level Remote Control & Hardwire Arming LevelEntry Delay Beeps Exit Delay BeepsSilent Emergency Alarms Silent Burglary AlarmsDisabling Quick Arming Automatic Restoral of Bypassed SensorsRemote Control & Hardwire ARM/DISARM Chirp Automation Output Mode During AlarmAutomation Output on During and After Alarm Automation Output on During AlarmRemote Access Password Automation Output During EXIT/ENTRY DelaysAutomation Output While Armed Automation Output PolarityAdding Additional User Codes Control Panel Master ResetRemoving Additional User Codes General Communicator Options Communicator ProgrammingWay manual, 3 2-way full duplex using this step Communicator EnableWAY Audio Voice ResponseCall Limiter Dialing DelayDialing Method Call Routing Reporting FormatAccount Number Telephone Number Delays and Special CharactersPrimary Telephone Number Secondary Telephone NumberReport Force Arming Report Control Panel TroubleOpening and Closing Reports Point ID ReportingSteps #201-206 General Reporting CodesFire and Emergency buttons and for each System Reporting CodesSteps #261-266 Force Arming Reporting CodeSteps #210-233 By 2 Format Point ID Alarm Report CodesBy 2 Format Point ID Trouble Report Codes Steps #234-257By 2 Format Point ID Reporting Codes Important Information
Top Page Image Contents