Roberts Gorden HE50ST Vent Pipe, Outside Air Inlet, Tubes, Gas Line, Burner Observation, Window

Page 67

 

SECTION 15: SERVICING INSTRUCTIONS

 

 

 

Vent Pipe

Venting must be intact. Using a flashlight, look for obstructions, cracks on the pipe,

 

gaps in the sealed areas or corrosion.

 

The area must be free of dirt and dust.

 

Remove any carbon deposits or scale using a wire brush.

 

See Page 49, Section 11.

 

 

 

Outside Air Inlet

Inlet must be intact. Look for obstructions, cracks on the pipe, gaps in the sealed

 

areas or corrosion.

 

The area must be free of dirt and dust. Clean and reinstall as required.

 

 

 

Tubes

Make sure there are no cracks.

 

Make sure tubes are connected and suspended securely.

 

See Page 11, Section 5.

 

Make sure there is no sagging, bending or distortion.

 

 

 

Gas Line

Check for gas leaks. See Page 52, Section 12.

 

 

 

Burner Observation

Make sure it is clean and free of cracks or holes.

Window

Clean and replace as required.

 

 

 

Blower Scroll, Wheel and

Compressed air or a vacuum cleaner may be used to clean dust and dirt.

Motor

 

 

 

 

 

Burner Cup and Orifice

Clear of obstructions (even spider webs will cause problems).

 

Carefully remove any dust and debris from the burner.

 

 

 

Electrode

Replace if there are cracked ceramics, excessive carbon residue, or erosion of the

 

electrode.

 

The electrode gap should be 3 mm.

 

 

 

Thermostat

There should be no exposed wire or damage to the thermostat.

 

See Page 54, Section 13.

 

 

 

Suspension Points

Make sure the heater is hanging securely.

 

Look for signs of wear on the chain or ceiling.

 

See Page 11, Section 5.

Sports Hall Guard,

Decorative and Protective

Grilles (optional)

The grille must be securely attached. If the grille is loose or off, contact a contractor qualified in the installation and service of gas-fired heating equipment for repair.

Check that side reflector extensions are installed correctly and secured in place if necessary. (Decorative grille only.)

See Page 44, Section 10.3.3 and Page 45, Section 10.4.

Make sure shield is installed correctly and secured in place if necessary. (Decorative grille only.) See Page 44, Section 10.3.2.

Wall Tag

If a wall tag is present, make sure it is legible and accurate. Please contact

 

Roberts-Gordon LLC or your ROBERTS GORDON® independent distributor if you

 

need a wall tag. See Page 4, Section 2.1.

 

 

61 of 73

Image 67
Contents Owner If you smell gasPage Roberts-Gordon Europe Limited Table of ContentsPage Table of Figures Bottom and Back Panel Label PlacementPage Product Approval Heater Safety Control Side Label Placement Low Level User Instructions Installer ResponsibilityNational Standards and Applicable Codes Clearances to Combustibles Model Clearances Data Linear and Double LinearHE40ST HE45ST HE50ST HE45ST HE50ST HE15ST HE30DLHE30UT HE15UTHE20UT HE25UTTUBE, Protective Grille TUBE, Opposite 45 TiltMajor Component Descriptions General Suspension Details Typical Suspension Details Linear Standard Parts List Linear & Double Linear Heater InstallationDescription Linear General Assembly Overview HE35ST HE40ST f HE15ST f HE20ST HE25ST fHE45ST HE50ST f Double Linear Standard Parts List Double Linear General Assembly Overview HE60DL HE70DL f HE30DL fClosed Burner Tube InstallationCoupling and Tube Assembly Open2 Coupling and Tube Assembly 1 Coupling and Tube AssemblyTighten slide bar as shown below Tube Clamp Package Installation Hanger Option a Option BFan Tube Weld Spot Coupling Tee Tube Standard Parts List Tube Heater InstallationLockwasher 6mm Blackheat HE Tube Assembly OverviewHE30UT HE35UT g HE15UT g HE20UT gHE45UT g Burner Tube and Fan Tube Installation U-tube Hanger PlacementU-tube Support Bracket Assembly Installation 1 Tube Clamp Package InstallationTube, Standard Tube, Opposite Orient coupling so that Impact block is U-tube Installation Tube InstallationReflector 02750303 Reflector Support Strap 03050000 Screw #8 x 3/4 Multiburner Configuration & Installation Typical Manifold Layout Linear and U-Tube Configuration Burner Installation Burner & FAN InstallationStandard Fan Assembly Linear & U-tube Fan Installation IP55 Fan Assembly1 Double Linear Fan Installation Double Linear Fan InstallationNon-Return Valve Condensate Drain AssemblyOptional Heater Accessories 2 Side Reflector Installation Reflector Side Extension Installation 1 Bracket InstallationStep Tube Cover InstallationDistance a Extension 2 Frame Shield Installation3 Grille Installation 2 Grille End Cap Installation3 Mesh Guard Connection Sports Hall Guard Installation2 Fastener Installation 1 Grille InstallationUndershield Installation Undershield Installation 10.6.1 Hanger InstallationAdjust Undershield Height Wall Mounting Hardware InstallationVenting and Fresh AIR Supply Air Supply Requirements Outside Combustion Air SupplyCommon Duct Air Supply with Flue ConfigurationsGAS Piping Correct Positions Incorrect Positions Wrong InstallationTypical External Wiring Diagram Linear or U-Tube WiringTypical External Wiring Diagram Multiburner Typical External Wiring Diagram Double Linear OptionInternal Wiring Diagram Tubing may still be hot Heater Lockout Indicator by ConnectorOperation and service OperationSystem Checks Heater Lockout Indicator by Volt Free ConnectorTesting Commissioning MultiburnerServicing Instructions Automatic Flame Control Unit Pressure SwitchMaintenance Checklist ElectrodeGas Line Vent PipeOutside Air Inlet TubesTroubleshooting U-Tube Troubleshooting Flow Chart Linear, Double LinearTroubleshooting Flow Chart Linear, Double Linear and U-Tube Troubleshooting Flow Chart MultiburnerTroubleshooting Flow Chart Multiburner Manometer 4 3 2 1 0 1 2 3 4 5 Manifold Gas Pressure SettingReplacement Parts V2 W3 Description Quantity Viewer Window Replacement Package P/NDoor Gasket Replacement Package P/N Gas Valve Replacement Package P/NSpecifications Double Linear Heater Linear HeaterTube Heater Standard Burner Specifications Burner SpecificationsModels HE15 HE20 HE25 HE30 HE35 HE40 HE45 HE50 Page Page Maintain Clearance Side Clearance below