Heat & Glo LifeStyle SUPREME-I30-SP, GRAND-I35 Getting Started, Typical Appliance System

Page 16

4

Getting Started

Installer Guide

 

 

 

A. Typical Appliance System

NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

 

VERTICAL TERMINATION CAP

 

(SECTION 8.F)

 

VENT PIPE

 

(SECTION 8)

 

3 INCH FLEX LINERS

 

(SECTION 8)

 

MANTEL AND MANTEL LEG

 

SECTION 5.B AND 11.A

 

SURROUND OR FRONT

 

NOT SHOWN

 

SECTION 2.D AND 8.D.

 

HEARTH EXTENSION

GAS LINE (SECTION 9)

ACCESS THROUGH EXISTING

MASONRY OR WOODBURNING

FIREPLACE

Figure 4.1

Typical System

16

Heat & Glo • Grand-I35, Grand-I35-SP, Supreme-I30, Supreme-I30-SP2206-900 Rev. K • 6/11

Image 16
Contents What to do if you smell gas ModelsDo Discardnot Congratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear Space Nine Hour Safety Shutdown Feature Module ResetBefore Lighting Fireplace Lighting Instructions IPI Final inspection byLighting Instructions Standing Pilot Ignition Do not Connect 110 VAC to the Control ValveFrequently Asked Questions After Appliance is LitMaintenance and Service Maintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionLogs FireboxBurner Ignition and Operation Standing Pilot Flame PatternsGetting Started Typical Appliance SystemTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Minimum Fireplace Opening Fireplace Size RequirementsTOP View Front View Side View Mantel and Wall Projections Side View TOP ViewTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVent Limits Venting ComponentsStanding Pilot Models Placing, Securing and Leveling the ApplianceIPI Models Masonry Factory Built Installing Adaptor and Termination CapDamper Flashing Kit Optional Gas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements Standing Pilot Ignition System WiringIntelliFire Plus Ignition System Wiring Electrical InformationOptional Wall Switch Rocker Thermostat or Remote ThermocoupleOptional Accessories Requirements FAN BladesFan Wiring with Remote See .H for control module operation instructionsFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup Install the Log Assembly Log Set Assembly LOGS-I35 Models GRAND-I35, GRAND-I35-SPLOG Support Pilot Grate Tines Bracket Grate BAR END of LOG Rests On Flat Spot Flat Spot for LOG Groove Flat Spot for Grate BARLOG #6 LOG #6 Resting on Flat Spots LOG #7 Resting on Flat Spots Log #6LOG Support LOG Rests on Grate Tine  G. Install the Log AssemblySlot Corner LOG Flush With Pilot Bracket For LOG #5Flat Spots Points of LOG Rest on For LOG #6Air Shutter Setting Air Shutter SettingsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionShorts in the wiring IntelliFire Plus Ignition SystemAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyStocked At DepotService Parts SUPREME-I30, SUPREME-I30-SP Metal Insert, IPIGRAND-I35 #19 IPI Valve AssemblySUPREME-I30 Service Parts GRAND-I35-SP, SUPREME-I30-SP #19 Standing Pilot Valve AssemblyStanding Pilot Conversion Kits Service Parts ListIPI Conversion Kits Contact Information