Heat & Glo LifeStyle SUPREME-I30-SP Log Set Assembly LOGS-I35 Models GRAND-I35, GRAND-I35-SP

Page 32

G. Install the Log Assembly

Log Set Assembly: LOGS-I35

Models: GRAND-I35, GRAND-I35-SP

CAUTION: Logs are fragile, handle with care.

#1

#4

 

SRV2205-702

 

SRV2205-704

#2

#5

SRV2205-710

 

SRV2205-701

 

 

#6

SRV2205-703

 

 

#3

SRV2205-705

 

 

 

 

#7

 

 

 

SRV2205-706

LOG SUPPORT

PILOT

GRATE TINES

BRACKET

GRATE BAR

Figure 1. Log Set Installed

Figure 2. Reference Points

REST LOG #6

REST LOG #5HERE

HERE

1

REST NOSE OF LOG ON LOG SUPPORT

LOG NOSE

MATE TINE

WITH LOG

GROOVE

Figure 3. Log #1

Figure 4. Log #1

Log #1 (SRV2205-702)Position Log #1 as shown in Figure 3. Mate the left grate tine with the log groove. Rest the nose of the log on the log support as shown.

32

Heat & Glo • Grand-I35, Grand-I35-SP, Supreme-I30, Supreme-I30-SP2206-900 Rev. K • 6/11

Image 32
Contents Do Discardnot ModelsWhat to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear SpaceBefore Lighting Fireplace Module Reset Nine Hour Safety Shutdown Feature Lighting Instructions IPI Final inspection byLighting Instructions Standing Pilot Ignition Do not Connect 110 VAC to the Control ValveFrequently Asked Questions After Appliance is LitMaintenance and Service Maintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionLogs FireboxBurner Ignition and Operation Standing Pilot Flame PatternsGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed TOP View Front View Side View Fireplace Size RequirementsMinimum Fireplace Opening Mantel and Wall Projections Side View TOP ViewTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVent Limits Venting ComponentsIPI Models Placing, Securing and Leveling the ApplianceStanding Pilot Models Damper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Gas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements Standing Pilot Ignition System WiringIntelliFire Plus Ignition System Wiring Electrical InformationOptional Wall Switch Rocker Thermostat or Remote ThermocoupleOptional Accessories Requirements FAN BladesFan Wiring with Remote See .H for control module operation instructionsFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup LOG Support Pilot Grate Tines Bracket Grate BAR Log Set Assembly LOGS-I35 Models GRAND-I35, GRAND-I35-SPInstall the Log Assembly LOG #6 LOG Groove Flat Spot for Grate BAREND of LOG Rests On Flat Spot Flat Spot for LOG #6 Resting on Flat Spots LOG #7 Resting on Flat Spots Log #6Slot  G. Install the Log AssemblyLOG Support LOG Rests on Grate Tine Corner LOG Flush With Pilot Bracket For LOG #5Flat Spots Points of LOG Rest on For LOG #6Air Shutter Setting Air Shutter SettingsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Troubleshooting Symptom Possible Cause Corrective ActionShorts in the wiring IntelliFire Plus Ignition SystemAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyStocked At DepotService Parts SUPREME-I30, SUPREME-I30-SP Metal Insert, IPISUPREME-I30 #19 IPI Valve AssemblyGRAND-I35 Service Parts GRAND-I35-SP, SUPREME-I30-SP #19 Standing Pilot Valve AssemblyIPI Conversion Kits Service Parts ListStanding Pilot Conversion Kits Contact Information