Heat & Glo LifeStyle GRAND-I35-SP, SUPREME-I30-SP owner manual Appliance Setup

Page 31

12 Appliance Setup

A. Remove Glass Assembly

See Section 12.H.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the firebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of ap- proved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional acces- sories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

F. Ember Placement

WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place the ember material:

Embers CANNOT be placed directly over ports. Care should be taken not to cover the lighting trail of ports (from back to front).

Place dime-size pieces of Glowing Embers® just in front of the port trail, but not on or in between the ports (see Figure 12.2). Care should be taken so that the ports are not covered. Failure to follow this procedure will likely cause lighting and sooting problems.

Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

E. Place the Lava Rock

WARNING! Risk of Explosion! Follow lava rock place- ment instructions in manual. DO NOT place lava rock on burner. Improperly placed lava rock interferes with proper burner operation.

Lava rock is shipped with this gas appliance. To place the lava rock:

Lava rock CANNOT be placed on the burner.

Place lava rock in front of and to the sides of the burner.

PLACE LAVA ROCK IN SHADED AREA ONLY

Figure 12.1 Placement of Lava Rock

EMBERS NOT

ALLOWED IN

PILOT AREA

Figure 12.2 Placement of Embers

Heat & Glo • Grand-I35, Grand-I35-SP, Supreme-I30, Supreme-I30-SP2206-900 Rev. K • 6/11

31

Image 31
Contents What to do if you smell gas ModelsDo Discardnot Homeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches IPI Battery Tray/Battery Installation Nine Hour Safety Shutdown Feature Module ResetBefore Lighting Fireplace Final inspection by Lighting Instructions IPIDo not Connect 110 VAC to the Control Valve Lighting Instructions Standing Pilot IgnitionAfter Appliance is Lit Frequently Asked QuestionsMaintenance and Service Firebox Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection LogsStanding Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Minimum Fireplace Opening Fireplace Size RequirementsTOP View Front View Side View Side View TOP View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent LimitsStanding Pilot Models Placing, Securing and Leveling the ApplianceIPI Models Masonry Factory Built Installing Adaptor and Termination CapDamper Flashing Kit Optional Gas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsStanding Pilot Ignition System Wiring IntelliFire Plus Ignition System WiringThermocouple Optional Wall Switch Rocker Thermostat or RemoteFAN Blades Optional Accessories RequirementsSee .H for control module operation instructions Fan Wiring with RemoteClearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup Install the Log Assembly Log Set Assembly LOGS-I35 Models GRAND-I35, GRAND-I35-SPLOG Support Pilot Grate Tines Bracket Grate BAR END of LOG Rests On Flat Spot Flat Spot for LOG Groove Flat Spot for Grate BARLOG #6 Log #6 LOG #6 Resting on Flat Spots LOG #7 Resting on Flat SpotsLOG Support LOG Rests on Grate Tine  G. Install the Log AssemblySlot For LOG #6 Corner LOG Flush With Pilot BracketFor LOG #5 Flat Spots Points of LOG Rest onAir Shutter Settings Air Shutter SettingSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Shorts in the wiringReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsAt Depot Service PartsLog Set Assembly StockedMetal Insert, IPI Service Parts SUPREME-I30, SUPREME-I30-SPGRAND-I35 #19 IPI Valve AssemblySUPREME-I30 #19 Standing Pilot Valve Assembly Service Parts GRAND-I35-SP, SUPREME-I30-SPStanding Pilot Conversion Kits Service Parts ListIPI Conversion Kits Contact Information