0 mm to 1 in. (25 mm) Thick Inside Fit Method
The Tonic decorative front is approved for inside fit ap- plications.
For the Tonic decorative front inside fit applications, the decorative front must be installed tight to the finishing flanges and must not overlap any finish material.
Ensure that no
BOARD
|
|
|
|
|
|
|
|
|
| 1 in. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| (MAX) |
| 3/4 in. | |
|
|
|
|
|
|
|
|
|
|
| (19 mm) | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3/4 in. | 3/4 in. |
(19 mm) | (19 mm) |
| 3 in. |
| (76 mm) |
| Bottom Joint |
Figure 13.11 Noncombustible Surface Finishing Material 0 - 1 in. (25 mm) Thick-Inside Fit Method (Tonic Decorative Front Only)
D. Decorative Fronts
WARNING! Risk of Fire! A decorative front is required for this model. DO NOT operate this appliance without a decorative front in place.
Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used.
Inside and Overlap Method
See Section 13.C.
DRYWALL OR EQUIVALENT 3/8 in. (10 mm)
APPLIANCE OPENING (HEIGHT)
3 in. (76 mm)
1 in.
TONIC DECORATIVE FRONT
Figure 13.12 Tonic Decorative Front
Inside-Fit Method Only
See Section 13.C.
Figure 13.10 Inside Fit Method (Tonic Decorative Front Only)
MARTINI DECORATIVE FRONT
Figure 13.13 Martini Decorative Front
58 | Heat & Glo • |