Wiring the PVK-80 Power Vent

NOTE: The PVK-80 Power Vent must terminate in a HORI- ZONTAL position. See Figure 7.31.

2.Install vent system components per planned vent run. Route the vent pipe from the fireplace to the Power Vent using the minimum number of elbows possible.

3.After determining the location of the vent system termina- tion point (see Step 1) cut a 10 in. X 12 in. rectangular hole through the wall or roof. Apply the adhesive back fiberglass tape to the last vent system component 1 1/4" from the edge. Firmly press the tape on to the venting and fold the extra tape inside the venting. See Figure 7.32. Mount and attach the power vent to the last vent system component. The exhaust port of the PVK-80 cap MUST be pointed down. Fasten the last horizontal vent section to the exterior firestop with a sheet metal screw through the flange and into the vent pipe. See Figure 7.33.

1 IN.	3 IN.	Note: Cut away
	3 IN.	Note: Cut away
		combustible
		siding for proper
		clearance.

FIBERGLASS TAPE

FOLD EDGE INSIDE PIPE

Figure 7.32

NOTE: Wall firestops (not included with the Power Vent) are available for DVP vent pipe. The firestop MUST be used whenever a section of vent pipe passes through a combustible wall.

5.The minimum distance from the outside wall to the end of the top shield of the PVK-80 horizontal cap is 14-1/2 inches. The maximum distance is 21 inches. See Figure 7.34.

6.Two support braces are provided and MUST be used to mount the PVK-80 horizontal cap to the wall. Screw one end of each brace to the bottom of the cap housing, using the pilot holes in the cap. Extend each brace until it contacts the building wall and tighten the bolt/nut in the center of each brace. Fasten the other end of each brace to the outside wall. See Figure 7.34.

FAN EXHAUST PORT MUST BE DOWN

Figure 7.33

14-1/2 in. MINIMUM

21 in. MAXIMUM

3 in.

1 in.

Figure 7.34			SUPPORT BRACES
			SUPPORT BRACES

NOTE: Electrical wiring must be done in accordance with national, provincial, and/or local electric codes.

CAUTION! Before performing any maintenance, repair, or electrical wiring to the fireplace/power vent, make sure the electrical power is first disconnected to the fireplace/ power vent.

PLACE TERMINAL BLOCK BEHIND FAN.

ACCESS FROM FRONT

WIRE ACCESS HOLE

Figure 7.35

Heat & Glo • RED60 • 2159-900 Rev. R • 9/12

RED60 2159-900 specifications

The Heat & Glo LifeStyle RED60 2159-900 is a modern and innovative gas fireplace that exemplifies cutting-edge design and advanced heating technology. With its sleek aesthetics and smart features, this fireplace is designed to elevate both comfort and style in any living space.

One of the main features of the RED60 is its impressive heat output. This model boasts a high efficiency rating, ensuring that homeowners can enjoy warmth without excessive energy consumption. The fireplace can deliver an output of up to 60,000 BTUs, making it suitable for both large and small areas. This efficient performance means less environmental impact, aligning with the growing emphasis on sustainability in home heating solutions.

The design of the Heat & Glo LifeStyle RED60 is another standout aspect. Its expansive glass viewing area provides a panoramic view of the flames, creating a beautiful focal point in any room. The minimalist frame enhances the contemporary aesthetic, allowing it to seamlessly complement various interior styles, from modern chic to traditional elegance.

In terms of technology, the RED60 incorporates advanced combustion systems, ensuring cleaner emissions without sacrificing performance. This technology not only contributes to a healthier indoor environment but also helps reduce the carbon footprint associated with home heating. Additionally, the fireplace features a patented heat distribution system, which optimally circulates warmth throughout the space, eliminating cold spots and enhancing overall comfort.

The RED60 also offers convenience through its intuitive remote control system. Users can easily adjust the flame height, heat output, and even set timers, providing ultimate flexibility in managing their indoor climate. For those who prefer a more hands-on approach, manual controls are also available, making it user-friendly for everyone.

Moreover, the installation process is simplified with the unit's flexible venting options, which can accommodate various configurations to suit different homes. Whether designing for a new build or retrofitting an existing space, this versatility appeals to homeowners and builders alike.

In summary, the Heat & Glo LifeStyle RED60 2159-900 is a blend of style, efficiency, and advanced technology. Its high heat output, sleek design, and intuitive controls make it an excellent choice for anyone seeking to enhance their living environment with a modern gas fireplace.