Heat & Glo LifeStyle owner manual Models RED40 RED40ST, Notice, •What to do if you smell gas

Page 1
Owner’s Manual

Owner’s Manual

Installation and Operation

Models:

RED40

RED40ST

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

Models: WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

DO NOT store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-DO NOT try to light any appliance.

-DO NOT touch any electrical switch. DO NOT use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard, Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

NOTICE WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. o • 7/12

1

 

Image 1
Contents NOTICE Models RED40 RED40ST•What to do if you smell gas Owner’s ManualHomeowner Reference Information A. CongratulationsSafety Alert Key Table of ContentsInstaller Guide 3 Maintenance and Service15 Troubleshooting 14 Appliance Setup = Contains updated information 13 FinishingLIMITED LIFETIME WARRANTY B. Limited Lifetime WarrantyWARRANTY COVERAGE WARRANTY PERIODWARRANTY CONDITIONS B. Limited Lifetime Warranty continuedWARRANTY EXCLUSIONS This warranty is void if1 Listing and Code Approvals D. High Altitude InstallationsA. Appliance Certification B. Glass SpecificationsInstallation of Carbon Monoxide Detectors 2 Operating Instructions User Guide A. Gas Fireplace SafetyB. Your Fireplace C. Clear SpaceD. Decorative Doors and Fronts E. Fixed Glass AssemblyG. Before Lighting Fireplace erate fireplace with fixed glass assembly removedFinal inspection by H. Lighting Instructions IPIFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS IPII. After Fireplace is Lit J.Frequently Asked QuestionsInitial Break-inProcedure •Some people may be sensitive to smoke and odorsA. Maintenance Tasks-Homeowner 3 Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection B.Maintenance Tasks-QualifiedService TechnicianVenting FireboxA. Typical Appliance System Getting StartedInstaller Guide Figure 4.1 Typical SystemC.Tools and Supplies Needed B. Design and Installation ConsiderationsD. Inspect Appliance and Components A. Selecting Appliance Location 5 Framing and Clearances1/2 IN. C 1/2 INFigure 5.2 Appliance Locations RED40ST C. Clearances B. Constructing the Appliance ChaseMINIMUM FRAMING DIMENSIONS Dimensions of Non-Combustibles D. Mantel and Wall ProjectionsCombustible Mantels Non-CombustibleMantelsA. Vent Termination Minimum Clearances 6 Termination LocationsRoof Pitch H Min. FtCovered Alcove Applications = AREA WHERE TERMINAL IS NOT PERMITTEDV= VENT TERMINAL X = AIR SUPPLY INLET E. Vent Diagrams 7 Vent Information and DiagramsA. Approved Pipe B. Vent Table KeyVenting with 1 elbow Top Vent - Horizontal TerminationV1 Minimum H1 MaximumVenting with 2 elbows 1. Top Vent - Horizontal Termination - continuedINSTALLED HORIZONTALLY H1 + H2 MaximumVenting with 3 elbows 1. Top Vent - Horizontal Terminationcontinued H2 V2 H1 V1V = 3 ft Min. 1m, 50 ft. Max. 15.2 m Top Vent - Vertical Termination No ElbowsExhaust restrictor Instructions V2 H1 V1 Top Vent - Vertical TerminationVenting with 3 elbows DIRECT VENT WITH 5 in. / 8 in. DIAMETER DVP PIPE A. Pipe Clearances to Combustibles 8 Vent Clearances and FramingB. Wall Penetration Framing Between ceiling firestopsC. Install the Ceiling Firestop Flat Ceiling Installation D. Install Attic Insulation ShieldVaulted Ceiling Installation A. Appliance Preparation 9 Appliance PreparationSetting the Fireplace into the Framing B. Securing and Leveling the ApplianceWARNING! Risk of Fire! Prevent contact with •Sagging or loose insulationC. Active Convection Technology A. Assemble Vent Sections 10 Installing Vent Pipe DVP PipeC. Secure The Vent Sections B. Assemble Slip SectionsPilot hole D. Disassemble Vent Sections E. Install Decorative Ceiling ComponentsG. Assemble and Install Storm Collar F. Install Metal Roof FlashingCAULK CAUTION! Risk of Cuts, Abrasions or Flying DebrisH. Install Vertical Termination Cap Figure 10.20 Venting Through the Wall J. Install Horizontal Termination CapA. Fuel Conversion 11 Gas InformationB. Gas Pressure •Ensure adequate ventilation C. Gas ConnectionB. IntelliFire Ignition System Wiring A. Wiring RequirementsC. Optional Accessories Requirements 12 Electrical InformationREMOTE RECEIVER Optional Remote Control Receiver LocationSWITCH TRIPPED D. Optional LED Lighting CircuitCOLOR PRODUCED F. Junction Box Installation E. Electrical Service and RepairG. Active Convection Blower Replacement KNOCKOUTFAN MOUNT FASTENER SIDE BURNER SCREWBLOWER TAB ON MOUNTING PLATE SLOT ON BLOWER HOUSINGFigure 12.17. Remove Mounting Plate Figure 12.18. Removed Mounting PlateA. Splatter Guard 13 FinishingB. Framing and Finishing Instructions Finishing InstructionsFinishing Around Opening with Gypsum Wallboard Finish and Sealing JointsPainting Figure 13.1 Finishing DetailsDimensions of Combustibles C. Mantel and Wall ProjectionsFigure 13.5 Framing and Framing Materials-RED40 D. Facing MaterialFigure 13.6 Framing and Framing Materials-RED40ST 0 - 1 inch thickness-OverlapFit Method Non-CombustibleFinish MaterialsFigure 13.7 Overlap Fit Method Figure 13.9 Inside Fit Method 0 Inches to 4 Inches Thick Inside Fit Method42-3/4IN 13-1/8INASSEMBLY E. Mesh FrontsMESH FRAME ASSEMBLY Figure 13.11. Mesh Front InstallationA. Remove Fixed Glass Assembly 14 Appliance SetupC. Clean the Appliance D. AccessoriesI. Install the Mesh H. Fixed Glass AssemblyJ. Air Shutter Setting Removing Fixed Glass AssemblyA. IntelliFire Ignition System 15 TroubleshootingSymptom Possible CauseIntelliFire Ignition System - continued 16 Reference Materials A. Appliance Dimension DiagramM N O P Figure 16.2 Appliance Dimensions RED40STT R Q S A F GFigure 16.2 DVP vent components B. Vent Components DiagramsDVP-AS2 DVP-TRAP1 B. Vent Components Diagrams continuedDVP-TRAP2 DVP-TRAPK131 in 13 in 8-1/8in206 mm 330 mmDESCRIPTION Optional Wire HarnessPART NUMBER RED40 C. Service Partsat Depot Stocked40 in Landscape See-ThruDV Fireplace RED40STService Parts List #13 Control Assembly#14 Valve Assembly RED40,RED40STRED40, RED40ST Service PartsStocked   15.3 #15 Base Pan No Lights with Media15.1 15.215.1 15.215.3 15.4Stocked at Depot #16 Base Pan With Lights and Media16.3 16.116.3 16.216.1 16.4Porcelain or No refractory #17 Base Pan No Lights or Media withRED40-NNNNo lights, No Rock, No Refractory RED40-NNPNo lights, No Rock, PorcelainRED40ST-NNNNo lights, No Rock, No Refractory Stocked at DepotRED40ST-NNPNo lights, No Rock, Porcelain RED40ST-NNGNo lights, No Rock, Granite#20 Porcelain --No Media #19 Granite --No Media#21 Granite --With Media #22 Porcelain --With MediaRED40ST NOTES D. Contact Information