Heat & Glo LifeStyle RED40ST owner manual C. Install the Ceiling Firestop

Page 33

C. Install the Ceiling Firestop

C. Install the Ceiling Firestop

A ceiling ﬁrestop MUST be used between ﬂoors and attics.

•DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ﬂoor (see Figure 8.3).

•Frame the area with the same sized lumber as used in ceiling/ﬂoor joist.

•The ceiling ﬁrestop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between ﬂoors that are not insulated. Refer to Figure 8.4.

•Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insu- lation around the vent. Insulation must be kept back from the pipe to prevent overheating.

		ATTIC ABOVE
		A
		A
	PIPE	A
	DVP	10 in. (254 mm)
Figure 8.3	Installing Ceiling Firestop

INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
	3 FASTENERS
	PER SIDE
CEILING FIRESTOP	CEILING FIRESTOP
INSTALLED BELOW CEILING	INSTALLED ABOVE CEILING
Figure 8.4 Installing the Attic Shield
Heat & Glo • RED40, RED40ST • 2155-900 Rev. o	• 7/12	33
Heat & Glo • RED40, RED40ST • 2155-900 Rev. o	• 7/12

Image 33

Contents NOTICE Models RED40 RED40ST•What to do if you smell gas Owner’s ManualHomeowner Reference Information A. CongratulationsSafety Alert Key Table of ContentsInstaller Guide 3 Maintenance and Service15 Troubleshooting 14 Appliance Setup = Contains updated information 13 FinishingLIMITED LIFETIME WARRANTY B. Limited Lifetime WarrantyWARRANTY COVERAGE WARRANTY PERIODWARRANTY CONDITIONS B. Limited Lifetime Warranty continuedWARRANTY EXCLUSIONS This warranty is void if1 Listing and Code Approvals D. High Altitude InstallationsA. Appliance Certiﬁcation B. Glass SpeciﬁcationsInstallation of Carbon Monoxide Detectors 2 Operating Instructions User Guide A. Gas Fireplace SafetyB. Your Fireplace C. Clear SpaceD. Decorative Doors and Fronts E. Fixed Glass AssemblyG. Before Lighting Fireplace erate ﬁreplace with ﬁxed glass assembly removedFinal inspection by H. Lighting Instructions IPIFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS IPII. After Fireplace is Lit J.Frequently Asked QuestionsInitial Break-inProcedure •Some people may be sensitive to smoke and odorsA. Maintenance Tasks-Homeowner 3 Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection B.Maintenance Tasks-QualiﬁedService TechnicianVenting FireboxA. Typical Appliance System Getting StartedInstaller Guide Figure 4.1 Typical SystemB. Design and Installation Considerations C.Tools and Supplies NeededD. Inspect Appliance and Components A. Selecting Appliance Location 5 Framing and Clearances1/2 IN 1/2 IN. CFigure 5.2 Appliance Locations RED40ST C. Clearances B. Constructing the Appliance ChaseMINIMUM FRAMING DIMENSIONS Dimensions of Non-Combustibles D. Mantel and Wall ProjectionsCombustible Mantels Non-CombustibleMantelsA. Vent Termination Minimum Clearances 6 Termination LocationsRoof Pitch H Min. Ft= AREA WHERE TERMINAL IS NOT PERMITTED Covered Alcove ApplicationsV= VENT TERMINAL X = AIR SUPPLY INLET E. Vent Diagrams 7 Vent Information and DiagramsA. Approved Pipe B. Vent Table KeyVenting with 1 elbow Top Vent - Horizontal TerminationV1 Minimum H1 MaximumVenting with 2 elbows 1. Top Vent - Horizontal Termination - continuedINSTALLED HORIZONTALLY H1 + H2 MaximumVenting with 3 elbows 1. Top Vent - Horizontal Terminationcontinued H2 V2 H1 V1Top Vent - Vertical Termination No Elbows V = 3 ft Min. 1m, 50 ft. Max. 15.2 mExhaust restrictor Instructions V2 H1 V1 Top Vent - Vertical TerminationVenting with 3 elbows DIRECT VENT WITH 5 in. / 8 in. DIAMETER DVP PIPE A. Pipe Clearances to Combustibles 8 Vent Clearances and FramingB. Wall Penetration Framing Between ceiling ﬁrestopsC. Install the Ceiling Firestop D. Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation A. Appliance Preparation 9 Appliance PreparationSetting the Fireplace into the Framing B. Securing and Leveling the ApplianceWARNING! Risk of Fire! Prevent contact with •Sagging or loose insulationC. Active Convection Technology A. Assemble Vent Sections 10 Installing Vent Pipe DVP PipeB. Assemble Slip Sections C. Secure The Vent SectionsPilot hole D. Disassemble Vent Sections E. Install Decorative Ceiling ComponentsG. Assemble and Install Storm Collar F. Install Metal Roof FlashingCAULK CAUTION! Risk of Cuts, Abrasions or Flying DebrisH. Install Vertical Termination Cap Figure 10.20 Venting Through the Wall J. Install Horizontal Termination Cap11 Gas Information A. Fuel ConversionB. Gas Pressure •Ensure adequate ventilation C. Gas ConnectionB. IntelliFire Ignition System Wiring A. Wiring RequirementsC. Optional Accessories Requirements 12 Electrical InformationREMOTE RECEIVER Optional Remote Control Receiver LocationD. Optional LED Lighting Circuit SWITCH TRIPPEDCOLOR PRODUCED F. Junction Box Installation E. Electrical Service and RepairG. Active Convection Blower Replacement KNOCKOUTFAN MOUNT FASTENER SIDE BURNER SCREWBLOWER TAB ON MOUNTING PLATE SLOT ON BLOWER HOUSINGFigure 12.17. Remove Mounting Plate Figure 12.18. Removed Mounting PlateA. Splatter Guard 13 FinishingB. Framing and Finishing Instructions Finishing InstructionsFinishing Around Opening with Gypsum Wallboard Finish and Sealing JointsPainting Figure 13.1 Finishing DetailsDimensions of Combustibles C. Mantel and Wall ProjectionsD. Facing Material Figure 13.5 Framing and Framing Materials-RED40Figure 13.6 Framing and Framing Materials-RED40ST Non-CombustibleFinish Materials 0 - 1 inch thickness-OverlapFit MethodFigure 13.7 Overlap Fit Method Figure 13.9 Inside Fit Method 0 Inches to 4 Inches Thick Inside Fit Method42-3/4IN 13-1/8INASSEMBLY E. Mesh FrontsMESH FRAME ASSEMBLY Figure 13.11. Mesh Front InstallationA. Remove Fixed Glass Assembly 14 Appliance SetupC. Clean the Appliance D. AccessoriesI. Install the Mesh H. Fixed Glass AssemblyJ. Air Shutter Setting Removing Fixed Glass AssemblyA. IntelliFire Ignition System 15 TroubleshootingSymptom Possible CauseIntelliFire Ignition System - continued 16 Reference Materials A. Appliance Dimension DiagramM N O P Figure 16.2 Appliance Dimensions RED40STT R Q S A F GB. Vent Components Diagrams Figure 16.2 DVP vent componentsDVP-AS2 DVP-TRAP1 B. Vent Components Diagrams continuedDVP-TRAP2 DVP-TRAPK131 in 13 in 8-1/8in206 mm 330 mmOptional Wire Harness DESCRIPTIONPART NUMBER RED40 C. Service Partsat Depot Stocked40 in Landscape See-ThruDV Fireplace RED40STService Parts List #13 Control Assembly#14 Valve Assembly RED40,RED40STRED40, RED40ST Service PartsStocked   15.3 #15 Base Pan No Lights with Media15.1 15.215.1 15.215.3 15.4Stocked at Depot #16 Base Pan With Lights and Media16.3 16.116.3 16.216.1 16.4Porcelain or No refractory #17 Base Pan No Lights or Media withRED40-NNNNo lights, No Rock, No Refractory RED40-NNPNo lights, No Rock, PorcelainRED40ST-NNNNo lights, No Rock, No Refractory Stocked at DepotRED40ST-NNPNo lights, No Rock, Porcelain RED40ST-NNGNo lights, No Rock, Granite#20 Porcelain --No Media #19 Granite --No Media#21 Granite --With Media #22 Porcelain --With MediaRED40ST NOTES D. Contact Information