Heat & Glo LifeStyle 6000 XLS, 6000 GDVFL manual Heat-N-Glo Fireplace

Page 1

Heat-N-Glo Fireplace

Models:

6000 GDVFL

6000 XLS

Installers Guide

U.S. Patents 4,793,322; 4,875,464; 5,000,162 and Patents Pending Canadian Patent 1,297,746

A.G.A. Design Certified/CGA Certified and Underwriters Laboratories Listed. See Approvals Tabel on Page 1.

WARNING

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.

- Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance.

-What to do if you smell gas

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

-Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

Printed in U.S.A.

Copyright 1997,

Heat-N-Glo Fireplace Products, Inc.

6665 West Highway 13, Savage, MN 55378

READ THIS MANUAL BEFORE INSTALLING OR OPERATING THIS APPLIANCE. THIS INSTALLERS GUIDE MUST BE LEFT WITH APPLIANCE FOR FUTURE REFERENCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, SERVICE AGENGY, OR THE GAS SUPPLIER.

1.This appliance may be installed in an

aftermarket, permanently located, manufactured (mobile) home, where not prohibited by local codes.

2.This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

Please contact your Heat-N-Glo Fireplace dealer for any questions or concerns. For the number of your nearest Heat-N-Glo dealer, please call 612-890-8367.

446-982-A 8/97

Image 1
Contents Heat-N-Glo Fireplace Safety and Warning Information Replacement Parts Table of ContentsHigh Altitude Installations Installation CodesApprovals and Codes CodesGetting Started Diagram of the6000 Series Step Installing the FireplaceLocating FireplaceModel Models Step Framing Fireplace26-1/4 Vent System Approvals Step Installing Vent SystemDV-90D Corner Installation Venting with One 90 Elbow Venting with Two 90 Elbows Venting with three 90 elbows Attach the First Vent Component to the Starting Collars Installing Vent ComponentsContinue Adding Vent Components Adding Venting Components Install Support BracketsInstalling Support Brackets 4. Install Firestops 12 Hole and Vent Pipe 11 Hole and New Framing Members Attic Firestop Vent TerminationRound and Trapezoid Termination Caps If Exterior Walls are Finished with Major U.S. Building Codes Minimum Height from Roof to Lowest Discharge Opening Step Gas Control Systems Step Positioning Leveling, Securing FireplaceStanding Pilot Ignition System Direct Spark Ignition DSI SystemMm hook-up at the unit Step Gas Supply LinePressure Natural Gas Propane Step Gas Pressure RequirementsFor Standing Pilot Ignition Wiring Step Wiring FireplaceOptional Accessories Remote Wall SwitchFan Wiring Diagram For Direct Spark Ignition DSI WiringStep Finishing Direct Spark Ignition DSI Wiring DiagramInstalling the Trim Step Installing Trim Logs, Ember MaterialHearth Extensions Save the log instructions with this manual Positioning the LogsPlacing the Ember Material Glass Assembly Review safety warnings and cautions Step Before Lighting Fireplace After InstallationDouble-check for faulty components Double-check for gas leaksMaintaining and Servicing Your Fireplace Fireplace MaintenanceBurner Flame Patterns Standing Pilot Only Replacement Parts AccessoriesDSI Ignition Only 20 X Both Standing Pilot and DSI Ignition6000XLS 20 X Models Mesh