Heat & Glo LifeStyle 6000 XLS, 6000 GDVFL manual Getting Started

Page 5

Introducing the

Heat-N-Glo

Gas Fireplaces

Pre-installation Preparation

Heat-N-Glo direct vent gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems.

Gas fireplace diagrams, including the dimensions, are shown in this section.

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass. Do not install any unit with damaged, incomplete, or substitute parts.

The vent system components and trim doors are shipped in separate packages. The gas logs are factory installed (Model 6000GDVFL) and are packaged separately and must be field installed (Model 6000XLS). Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner’s warranty and may present a fire hazard.

The Heat-N-Glo Fireplace Products, Inc. Warranty will be voided by, and Heat-N-Glo Fireplace Products, Inc. disclaims any responsibility for, the following actions:

•Installation of any damaged fireplace or vent system component.

•Modification of the fireplace or direct vent system.

•Installation other than as instructed by Heat-N-Glo Fireplace Products, Inc.

•Improper positioning of the gas logs or the glass door.

•Installation and/or use of any component part not manufactured and approved by Heat-N-Glo Fire- place Products, Inc., not withstanding any indepen- dent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

2

Getting

Started

2

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Heat-N-Glo Fireplace Safety and Warning Information Replacement Parts Table of ContentsHigh Altitude Installations Installation CodesApprovals and Codes CodesGetting Started Diagram of the6000 Series Step Installing the FireplaceLocating Fireplace26-1/4 Step Framing FireplaceModel Models Vent System Approvals Step Installing Vent SystemDV-90D Corner Installation Venting with One 90 Elbow Venting with Two 90 Elbows Venting with three 90 elbows Attach the First Vent Component to the Starting Collars Installing Vent ComponentsContinue Adding Vent Components Adding Venting Components Install Support BracketsInstalling Support Brackets 4. Install Firestops 12 Hole and Vent Pipe 11 Hole and New Framing Members Attic Firestop Vent TerminationRound and Trapezoid Termination Caps If Exterior Walls are Finished with Major U.S. Building Codes Minimum Height from Roof to Lowest Discharge Opening Step Gas Control Systems Step Positioning Leveling, Securing FireplaceStanding Pilot Ignition System Direct Spark Ignition DSI SystemMm hook-up at the unit Step Gas Supply LinePressure Natural Gas Propane Step Gas Pressure RequirementsFor Standing Pilot Ignition Wiring Step Wiring FireplaceOptional Accessories Remote Wall SwitchFan Wiring Diagram For Direct Spark Ignition DSI WiringStep Finishing Direct Spark Ignition DSI Wiring DiagramHearth Extensions Step Installing Trim Logs, Ember MaterialInstalling the Trim Placing the Ember Material Positioning the LogsSave the log instructions with this manual Glass Assembly Review safety warnings and cautions Step Before Lighting Fireplace After InstallationDouble-check for faulty components Double-check for gas leaksMaintaining and Servicing Your Fireplace Fireplace MaintenanceBurner Flame Patterns Standing Pilot Only Replacement Parts AccessoriesDSI Ignition Only 6000XLS 20 X Both Standing Pilot and DSI Ignition20 X Models Mesh
Top Page Image Contents