Vermont Casting DVT38S2 Lighting and Operating Instructions, To Turn Off Gas To Heater

Page 28

Chateau™ Decorative Gas Appliance

Lighting and Operating Instructions

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion

may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lit manually. When lighting the pilot follow these instructions exactly.

B.BEFORE LIGHTING smell all around the heater

area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance

Do not touch any electric switch

Do not use any phone in your building

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

If you cannot reach your gas supplier, call the Fire Department

C.Use only your hand to push in or turn the gas con- trol knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a quali- fied service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been un- der water. Immediately call a qualified service tech- nician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

Lighting Instructions

1.STOP! Read the “For Your Safety” information first and locate the control panel before lighting.

2.For TN/TP appliances ONLY, go on to Step 3. For RN/RP appliances turn the ON/OFF switch to OFF position or set thermostat to lowest set- ting.

3.Push in gas control knob slightly and turn to OFF” position. Do not force.

7.Turn knob on gas control to “PILOT”.

8.Push in control knob all the way and hold in until pilot indicator pointer moves from green to red (pilot is on). If the pointer does not move to red after several attempt, repeat Steps 3 to 7. When

3/8" - 1/2"

t

1

 

lo

 

F

P

 

i

2

F

O

F

 

O

F

 

 

 

5

4

3

 

 

SIT NOVA

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “What to do if you smell gas” in your “For your safety”. If you do not smell gas, go to the next step.

5.Remove glass door before lighting pilot. (See Glass Frame Removal section).

6.Visually locate pilot assembly by the main burner.

pointer moves to red, hold control knob in for about one (1) minute. relese knob and it will pop back into original position. Pilot should remain lit. If it goes out, repeat Steps 3 to 7.

If knob does not pop up when released, stop and immediately call your service technician or gas supplier.

If after several tries, the pilot will not stay lit, turn the gas control knob to “OFF” and call your service technician or gas supplier.

9.Replace glass door.

10.Turn gas control knob to “ON” position.

11.For RN/RP appliances turn the On/Off switch to “ON” position or set thermostat to desired setting.

To Turn Off Gas To Heater

1.Turn the On/Off switch to Off position or set the thermostat to lowest setting.

2.Turn off all electric power to the fireplace if service is to be performed.

3.Open control access panel.

4.Push in gas control knob slightly and turn clock-

wise to “OFF”. Do not force.

5.Close control access panel.

28

20009543

Image 28
Contents INSTALLER/CONSUMER Safety Information What to do if YOU Smell GASTable of Contents Locating Your Fireplace Installation & Operating InstructionsPlease Review the Following Carefully Dimension Standard FramingMantel Surround Framing CriticalMantels Clearance to CombustiblesHearth Framing and Finishing Nailing flangesGas Line Installation Final FinishingGas Specifications Gas Inlet and Manifold PressuresElectrical Junction Box E Units Only Remote ON/OFF SwitchElectronic Gas Control Valve General Venting Location of Vent TerminationCanadian Installations1 US Installations2 General Venting Information Termination LocationUSA Installations Canadian InstallationsGeneral Information Assembling Vent Pipes SK8 Venting Pipes Restrictor Plate Guide Horizontal TerminationVertical Termination ApplicationSidewall Applications Mm on the bottomAlways install horizontal venting on a level plane Sidewall InstallationStep Sidewall Installation with Stationary Glass Facing Outside Horizontal length requirementInstalling the 38S2VDK Door Installation ProcedureRestrictor plate use in straight up installation Turn shutter plate over to cover opening Vertical Through-the-Roof Installation Installing firestop spacerMin 610mm Chimney Components Component Description Model NumberGlass Frame Assembly Removal Glass CleaningRestrictor Plates Installation Operating InstructionsCeramic Refractory Installation Log, Lava Rock and Ember PlacementLava rock and ember placement Position the log front right. Hold the log Flame Characteristics Flame & Temperature AdjustmentRN/RP & EN/EP Models Trim Installation Trim frame in placeLighting and Operating Instructions To Turn Off Gas To HeaterLighting and Operating Instructions Lighting InstructionsTurning Off the Gas to the Appliance ValveTroubleshooting the Gas Control System SIT Nova 820 Millivolt ValveSIT 822 Valve with a Honeywell Electronic Ignitor Conversion Precautions Conversion ProcedureFuel Conversion Instructions Allow unit to cool if it has been operatingPilot Flame Adjustment Replace regulatorMaintenance Cleaning the Standing Pilot Control SystemCleaning Electronic Ignition System Battery Replacement for Ignitor ModuleDVT38S2 Decorative Gas Appliance DVT38S2 DVT38S2DVT38 Fuel Conversion KitsAccessories Remote ControlsFull Surround Mantel Model Functions ControlledLimited Lifetime Warranty Product Covered by this WarrantyEfficiency Ratings Model EnerGuide Ratings Fireplace Efficiency %