Hampton Direct H35-NG1, H35-LP1 installation manual Valve Description, But not overtightened

Page 26

INSTALLATION

AERATION

GAS PIPE

ADJUSTMENT

PRESSURE TESTING

5) The pressure check should be carried out

with the unit burning and the setting should

be within the limits specifi ed on the safety

label.

The burner aeration is factory set but may need adjusting due to either the local gas supply, air supply or altitude.

Natural Gas

1/4" (6.4 mm)

Propane

3/8" (9.5 mm)

The aeration adjustment gears are located on the right side of the burner box. Remove the Hampton® Logo plate on the right side of the unit to access the adjustment gears.

To adjust the aeration: use the allen key to turn the turning gear which will adjust the air shutter. Open the air shutter for a blue fl ame or close it for a yellower fl ame.

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

Themanifoldpressureiscontrolledbyaregulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1)Make sure the valve is in the "OFF" posi- tion.

2)Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide fl at screwdriver.

3)Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4)Light the pilot and turn the valve to "ON" position. Read manometer.

6) When fi nished reading manometer, turn

off the gas valve, disconnect the hose and

tighten the screw (clockwise) with a 1/8" fl at

screwdriver. Note: Screw should be snug,

but not overtightened.

Valve Description

1)Gas on/off knob

2)Manual high/low adjustment

3)Pilot Adjustment

4)Thermocouple Connection

5)Main Operator

6)Outlet Pressure Tap (Manifold Pressure)

7)Inlet Pressure Tap (Supply Pressure)

8)Pilot Outlet

9)Main Gas Outlet

10)Flange Securing Screw Holes

11)Alternative TC Connection Point

12)Thermoelectric Unit

13)Additional Valve Mounting Hole

Clockwise to open,

counter-clockwise to close.

Caution: Carbon will be produced if the air shutter is closed too much.

Note: Any damage due to carboning re- sulting from improperly setting the aeration controls is NOT covered under warranty.

Note: Aeration Adjustment should only be performed by an authorized Hamp- ton® Installeratthetimeofinstallation or service.

26

Hampton® H35 Direct Vent Freestanding Gas Stove

Page 25 Page 27
Image 26
Page 25 Page 27
Contents H35 Direct Vent Gas Fireplace Models H35-NG1 Natural Gas H35-LP1 PropaneTo the New Owner Unit DimensionsHampton Table of Contents Safety Label Copy of Safety LabelRequirements MA Code CO DetectorImportant Message Save These Instructions InstallationSpecifications Information for Mobile Manufactured Homes After First SaleClearances to Combustibles General Safety InformationInstallation Checklist This includesCombustion Locating YourGAS Stove Ventilation AIRSafety Precautions For the Installer InstallationPrecautions Exterior Vent Terminal Locations Rigid Pipe Venting Components List SV4LB6Horizontal Rigid Pipe Venting SystemsAlternate CapsVertical Terminations Systems for Rotating 45O Elbow for Straight Horizontal TerminationsVenting Arrangements Venting SystemsDura-Vent Snorkel Termination Horizontal Venting with Two 2 90o Elbows + H1 With these options, maxVertical Venting with Two 2 90o Elbows + V1 With these options, max. totalStraight Vertical Terminations Vertical Termination with CO-LINEAR Flex SystemRequired Parts Alternate Approved CapsDV Stove Horizontal Vent KIT A m O u l d be facing Down Nylsidingstandoff Termination Caps Planning Your Dura-Vent InstallationDURA-VENT Termination KIT Dura-Vent Basic Horizontal Kit #Below Grade Snorkel Installation DURA-VENT Horizontal InstallationsDiagram 1 Hint Apply silicone to female end Snorkel TerminationsDURA-VENT Vertical Termination Offset Chart This allows for small adjustmentsAppoved for US Installations Only Converting a Factory Built Metal ChimneyGAS Connection Cathedral CeilingsHigh Elevation Clockwise to open Counter-clockwise to close Valve DescriptionBut not overtightened Conversion KIT #791-969 from NG to LP LPG Conversion Kit Contains Qty DescriptionInstallation of the DC Sparker for the H35-1 Units Only Installation of the DC Sparker For the P90 Units Only Ground Wire from Kit Propane Conversion Kit 740-952 Contains Qty Conversion KIT to Lower BTU RatingNatural Gas Conversion Kit 740-950 Contains Qty Burner Orifi ce02-46 G LOG SET InstallationOptional Brick Panel 02-44 B 02-56 FLava rock Pins on Rear Log SupportPin Cutout Notch CutoutTop Tile Inset Double Door InstallationTile Inset Installation Side Tile InsetDoor Hinge Removal Remove screws Release catch by Pulling upWiring Diagrams InstructionsRemote Control Wall ThermostatOperating Instructions Automatic Convection FAN Operation Adjusting Flame HeightCopy of the Lighting Plate Instructions Normal Operating Sounds GAS Appliances MaintenanceMaintenance Instructions LOG Replacement General Vent MaintenanceFAN Maintenance Glass ReplacementRemoving Valve Installing Valve AssemblyTo remove valve from valve assembly, continue Replacing the FanParts List Main AssemblyBurner & LOG Assembly Brick Panel SETHampton H35 Direct Vent Freestanding Gas Stove Hampton H35 Direct Vent Freestanding Gas Stove Warranty ConditionsInstaller Please complete the following information

H35-NG1, H35-LP1 specifications

Hampton Direct has made significant strides in the home heating sector with its innovative products, particularly the H35-NG1 and H35-LP1 models. Both are designed to provide efficient heating solutions suitable for various residential settings.

The H35-NG1 is a natural gas unit, while the H35-LP1 runs on liquid propane, allowing homeowners to choose based on their available energy resources. One of the standout features of both models is their compact design, making them ideal for small spaces or rooms where traditional heaters would be impractical.

Another key characteristic is the user-friendly digital thermostat that comes with each unit. This feature allows homeowners to easily set and adjust their desired temperature, ensuring optimal comfort throughout the day while also promoting energy efficiency. The systems are equipped with smart technology that monitors usage patterns, helping homeowners make informed decisions about their heating needs.

Safety is also at the forefront of Hampton Direct's design. Both models include advanced safety features such as an automatic shut-off mechanism to prevent overheating and a fault detection system that alerts users to any issues. This commitment to safety provides peace of mind for homeowners as they enjoy the warmth provided by these heaters.

Additionally, both the H35-NG1 and H35-LP1 are engineered to minimize noise, ensuring a quiet operation that won't disrupt daily activities. This is particularly beneficial for bedrooms or living areas where a peaceful environment is desired.

The energy efficiency rating of these units is impressive, aligning with modern environmental standards. Homeowners can expect lower utility bills and a reduced carbon footprint as both heaters efficiently convert fuel into heat.

With robust construction materials designed to withstand high temperatures, both models promise durability and longevity with minimal maintenance required. This reliability ensures that consumers will not face frequent replacements, making the H35-NG1 and H35-LP1 sound investments for any home.

In summary, Hampton Direct's H35-NG1 and H35-LP1 models deliver effective and safe heating solutions with an emphasis on energy efficiency, user-friendliness, and quiet operation. Homeowners looking for a dependable heating system will find that these models embody quality and innovation, setting new standards in the home heating industry.
Top Page Image Contents