Hampton Direct H35-NG1, H35-LP1 Locating Your, GAS Stove, Combustion, Ventilation AIR

INSTALLATION

	LOCATING YOUR					OPTIONAL FAN INSTALLATION
		GAS STOVE	Fan Kit Contains:				7) Install locking grommet to power cord and
When selecting a location for your stove, ensure
			Qty.		Description		push through hole in the rear panel and give
that the clearances listed above are met as well			1		Fan Speed Controller with nut, and		a 1/4 turn to secure.
as ensuring that there is adequate accessibility					knob.
for servicing and proper operation.			1		Fan Assembly c/w green wire		NOTE: When running wires, keep them clear
					attached		ofvalveassemblyandtubingtoavoid
			1		Power cord		tangling of wires and valve.
			1		Plastic locking grommet		NOTE: Becarefulnottocutwireswhenpass-
			1)	Remove the Top Control Panel Assembly			ing through holes in the firebox.
				by removing the three screws. Diagram 1.			8) Rungreengroundwirefromfanandconnect
							to grounding lug.

A)	Cross Corner
B)	Room Divider
C)	Island
D)	Flat on Wall		Diagram 1
E) Flat on Wall Corner
F)	Flush with Wall/Alcove	2) Remove the nylon hole plug from the control
For Vent Termination requirements, see the			panel.	9) Connect green power cord ground wire to
"Exterior Vent Terminal Locations" section.		3)	Install the fan speed controller onto the	grounding lug.
			control panel and secure with nut. Connect	10) Run the neutral black wire from power cord
			remaining wire harness wires to speed
				and connect to fan motor.
			control. NOTE: Speed control wires must
	MANUFACTURED			11) Run the live black wire from power cord and
			be in the down position when control panel
	MOBILE HOME		is in place.	connect to speed control wire.
		4) Push black knob onto speed control.
	ADDITIONAL			12) Connect the white wire of the wire harness
	REQUIREMENTS	5) Remove the rear access panel on the back		to the fan terminal.
			of the stove by removing the 6 screws. Install	NOTE: Pull excess wire next to fan to
			the fan onto pins as per Diagram 2.
1) Ensure that structural members are not cut				avoid excessive heat from the firebox.
	or weakened during installation.

		13) Ensure all wires are pulled away from firebox
2) Ensure proper grounding using the #8		to avoid excessive heat and secure with
ground lug provided.		stick-on wire clip.
3) Appliance must be anchored to the fl oor		14) Re-attach control panel with 3 screws, re-
with the supplied anchoring methods.		versing step 1. Re-attach rear access panel
		with 6 screws, reversing step 5.
COMBUSTION AND		NOTE:Whenpowercordispluggedin,speed
		control is in the ON position and stove is
VENTILATION AIR		burning, allow 10 - 15 minutes for the ther-
	Diagram 2	modisc (temperature switch) to activate and
The combustion air from this appliance is drawn		turn on the Fan automatically.
from outside the building through the outer fl ue.	NOTE: Do NOT damage, cut or remove	WARNING:
Extra provision for combustion air inside the
room is not required.	the 3" aluminum air intake pipes.	Electrical Grounding Instructions
	Hint for pushing fan down onto pins - rub a	This appliance is equipped with
	bit of dish soap on the pins so the grommets	a three pronged (grounding) plug
	will slide down more easily. Check to make	for your protection against shock
	sure the fan is seated properly on the pins	hazard and should be plugged
	- try to move the fan back and forth.
	6) Push power cord through hole in the rear	directly into a properly grounded
		three-prong receptacle. Do not cut
	panel 14" - 16" and tie a loose knot in the	or remove the grounding prong
	cord on the inside to prevent the power cord	from this plug.
	from being pulled out. Diagram 2.
8	Hampton® H35 Direct Vent Freestanding Gas Stove