Hampton Direct H35-LP1, H35-NG1 General Safety Information, Installation Checklist, This includes

Page 7

INSTALLATION

manufactured home the unit must be bolted down to the fl oor.

4)This appliance is Listed for bedroom instal- lations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.

5)This appliance is Listed for Alcove installa- tions, maintain minimumAlcove clearances asfollows, minimumwidthof40"(1016mm), a maximum depth of 36" (914mm), and minimum ceiling height of 64" (1626mm) from fl oor to ceiling.

6)We recommend that you plan your instal- lation on paper using exact measurements for clearances and fl oor protection before actually installing this appliance. Have a qualifiedbuildinginspectorreviewyourplans before installation.

GENERAL SAFETY

INFORMATION

1)Theappliance installationmustconformwith local Canadian Electrical Code.

2)The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.

3)The appliance should be inspected for shipping damage before use and serv- iced annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpet- ing, bedding material, etc. It is imperative that control compartments, and circulating air passageways of the appliance be kept clean and free from excessive lint from carpeting.

4)See general construction and assembly instructions. The appliance and vent should be enclosed when installed in or passing through a living area, where children may come in contact with it.

5)This appliance must be connected to the specifi ed vent and termination cap to the

outside of the building envelope. Never

vent to another room or inside a building. Make sure that the vent is fi tted as per the instructions starting in the "Exterior Vent Terminal Locations" section.

6)Inspect the venting system annually for blockage and any signs of deterioration.

7)Venting terminals shall not be recessed into a wall or siding.

8)Any safety glass removed for servicing must be replaced prior to operating the ap- pliance.

9)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace.

Emissions from burning wood or gas could contain chemicals known to the State of Cali- fornia to cause cancer, birth defects or other reproductive harm.

INSTALLATION

CHECKLIST

1)Locate your appliance. Refer to the following sections:

a.Clearances to combustibles

b.Locating Your Gas Stove

c.For venting requirements, see "Venting Introduction" to "Venting Arrangements" sections.

2)Install Optional Fan. Refer to the "Optional Fan Installation" section.

3)Set vent restrictors. Refer to the "Vent Re- strictor Position" section.

4)Installventing.Refertothefollowingsections where applicable:

a.Check all venting requirements.

See "Venting Introduction" to "Venting Arrangements" sections.

b.Vertical Termination with Co-linear Flex System

c.DV Stove Horizontal Vent Kit

d.Dura-Vent Termination Kit.

5)Make gas connections. Refer to the "Gas Connection" section

Test the pilot. Must be as per diagram in the "Maintenance Instruction" section.

If converting to Propane, make changes prior see the "Conversion from Natrual Gas to Propane" section.

6)Test Gas Pressure. Refer to the "Gas Pipe Pressure Testing" section.

7)Install standard and optional features. Refer to the following sections where applicable:

a.Log Set Installation

b.Double Door Installation

c.Decorative Door Grill Installation

d.Tile Inset Installation

e.Wall Thermostat

f.Remote Control

8)Final check. Refer to the "Final Check" sec- tion.

Before leaving this unit with the customer, the installer must ensure that the appli- ance is fi ring correctly and operation fully explained to customer.

This includes:

1)Clocking the appliance to ensure the correct fi ring rate (rate noted on label) after burning appliance for 15 minutes.

2)Ifrequired,adjustingtheprimaryairtoensure that the fl ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

CLEARANCES TO

COMBUSTIBLES

The clearances listed are MINIMUM distances. Measure the clearance to both the appliance and the chimney connector. The farthest distance is correct if the two clearances do not coincide.

For example, if the appliance is set as indicated in one of the fi gures but the connector is too close, move the stove until the correct clearance to the connector is obtained.

This appliance may be installed only with the clearances as shown in the situations pictured.

Do not combine clearances from one type of installation with another in order to achieve closer clearances.

Hampton® H35 Direct Vent Freestanding Gas Stove

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Models H35-NG1 Natural Gas H35-LP1 Propane H35 Direct Vent Gas FireplaceHampton Unit DimensionsTo the New Owner Table of Contents Copy of Safety Label Safety LabelMA Code CO Detector RequirementsInformation for Mobile Manufactured Homes After First Sale InstallationSpecifications Important Message Save These InstructionsThis includes General Safety InformationInstallation Checklist Clearances to CombustiblesVentilation AIR Locating YourGAS Stove CombustionPrecautions InstallationSafety Precautions For the Installer Exterior Vent Terminal Locations SV4LB6 Rigid Pipe Venting Components ListCaps Rigid Pipe Venting SystemsAlternate HorizontalVenting Systems Rotating 45O Elbow for Straight Horizontal TerminationsVenting Arrangements Vertical Terminations Systems forDura-Vent Snorkel Termination + H1 With these options, max Horizontal Venting with Two 2 90o Elbows+ V1 With these options, max. total Vertical Venting with Two 2 90o ElbowsAlternate Approved Caps Vertical Termination with CO-LINEAR Flex SystemRequired Parts Straight Vertical TerminationsDV Stove Horizontal Vent KIT A m O u l d be facing Down Nylsidingstandoff Dura-Vent Basic Horizontal Kit # Planning Your Dura-Vent InstallationDURA-VENT Termination KIT Termination CapsSnorkel Terminations DURA-VENT Horizontal InstallationsDiagram 1 Hint Apply silicone to female end Below Grade Snorkel InstallationDURA-VENT Vertical Termination This allows for small adjustments Offset ChartConverting a Factory Built Metal Chimney Appoved for US Installations OnlyHigh Elevation Cathedral CeilingsGAS Connection But not overtightened Valve DescriptionClockwise to open Counter-clockwise to close LPG Conversion Kit Contains Qty Description Conversion KIT #791-969 from NG to LPInstallation of the DC Sparker for the H35-1 Units Only Installation of the DC Sparker For the P90 Units Only Ground Wire from Kit Burner Orifi ce Conversion KIT to Lower BTU RatingNatural Gas Conversion Kit 740-950 Contains Qty Propane Conversion Kit 740-952 Contains Qty02-44 B 02-56 F LOG SET InstallationOptional Brick Panel 02-46 GNotch Cutout Pins on Rear Log SupportPin Cutout Lava rockSide Tile Inset Double Door InstallationTile Inset Installation Top Tile InsetRemove screws Release catch by Pulling up Door Hinge RemovalInstructions Wiring DiagramsWall Thermostat Remote ControlOperating Instructions Copy of the Lighting Plate Instructions Adjusting Flame HeightAutomatic Convection FAN Operation Maintenance Instructions MaintenanceNormal Operating Sounds GAS Appliances Glass Replacement General Vent MaintenanceFAN Maintenance LOG ReplacementReplacing the Fan Installing Valve AssemblyTo remove valve from valve assembly, continue Removing ValveMain Assembly Parts ListBrick Panel SET Burner & LOG AssemblyHampton H35 Direct Vent Freestanding Gas Stove Hampton H35 Direct Vent Freestanding Gas Stove Conditions WarrantyInstaller Please complete the following information

H35-NG1, H35-LP1 specifications

Hampton Direct has made significant strides in the home heating sector with its innovative products, particularly the H35-NG1 and H35-LP1 models. Both are designed to provide efficient heating solutions suitable for various residential settings.

The H35-NG1 is a natural gas unit, while the H35-LP1 runs on liquid propane, allowing homeowners to choose based on their available energy resources. One of the standout features of both models is their compact design, making them ideal for small spaces or rooms where traditional heaters would be impractical.

Another key characteristic is the user-friendly digital thermostat that comes with each unit. This feature allows homeowners to easily set and adjust their desired temperature, ensuring optimal comfort throughout the day while also promoting energy efficiency. The systems are equipped with smart technology that monitors usage patterns, helping homeowners make informed decisions about their heating needs.

Safety is also at the forefront of Hampton Direct's design. Both models include advanced safety features such as an automatic shut-off mechanism to prevent overheating and a fault detection system that alerts users to any issues. This commitment to safety provides peace of mind for homeowners as they enjoy the warmth provided by these heaters.

Additionally, both the H35-NG1 and H35-LP1 are engineered to minimize noise, ensuring a quiet operation that won't disrupt daily activities. This is particularly beneficial for bedrooms or living areas where a peaceful environment is desired.

The energy efficiency rating of these units is impressive, aligning with modern environmental standards. Homeowners can expect lower utility bills and a reduced carbon footprint as both heaters efficiently convert fuel into heat.

With robust construction materials designed to withstand high temperatures, both models promise durability and longevity with minimal maintenance required. This reliability ensures that consumers will not face frequent replacements, making the H35-NG1 and H35-LP1 sound investments for any home.

In summary, Hampton Direct's H35-NG1 and H35-LP1 models deliver effective and safe heating solutions with an emphasis on energy efficiency, user-friendliness, and quiet operation. Homeowners looking for a dependable heating system will find that these models embody quality and innovation, setting new standards in the home heating industry.
Top Page Image Contents