Hampton Direct H35-LP1, H35-NG1 installation manual Conversion KIT #791-969 from NG to LP

Page 27

INSTALLATION

CONVERSION KIT #791-969 FROM NG TO LP

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one LPG Conversion Kit and one DC Sparker Kit.

LPG Conversion Kit Contains:

Qty. Part #

Description

1

904-529

5/32" Allen Key

1

904-645

Burner Orifi ce #51

1

918-590

Label "Converted to

 

 

LPG"

1

908-528

Red "LPG" label

1

910-037

LP Injector (Pilot Orifi ce)

1

918-487

Instruction Sheet

DC Sparker Kit Contains:

Qty. Part #

Description

1

820-475

Bracket DC Sparker

1

820-476

Bracket DC Sparker

1

904-153

Washer #8 External Star

1

904-330

Nut 8-32 Hex

1

904-438

Plug Nylon 0.750 Hole,

 

 

Black

1904-531 Bushing Split Plastic

0.500 in.

1904-543 Screw 8-32 x 3/4 Pan Head

2904-553 Screw #8 x 1/2 Type "B",

Black Oxide

1910-073 Spark Generator Battery Holder

1

910-074

Spark Generator Switch

 

 

C/W Wire

1910-078 Battery Size AA Energizer En91

2910-199 Clip Wire Holder

1910-903 Wire Fan To Power Cord Ground 30 in.

904-781 Velcro Hook, Black

904-782 Velcro Hook, Black

Installation of LPG

Conversion Kit:

1)Shut off the gas supply.

2)H35-1:Lift off the Cast Top and remove the glass front. Also, open up the control panel door.

P90-1:Remove the facade if it is in- stalled. Remove the glass door (refer to the glass door section in the manual).

3)Remove the logs, embers, and brick panels (if used).

4)Remove the 2 screws holding the Burner Assembly to the fi rebox base. Push the Burner Assembly to the left and lift out.

Remove the 2 screws, push Burner

Assembly to the left and lift out.

5)Pull off the pilot cap to expose the pilot orifi ce.

6)Unscrew the pilot orifi ce with the allen key and replace with the LP pilot orifi ce in the kit and replace pilot cap.

7)Remove burner orifi ce with a 1/2" wrench and discard. Use another wrench to hold on to the elbow behind the orifi ce.

Burner Orifi ce

8)Reinstall new burner orifi ce LP stamped #51 and tighten.

9) Turn control knob to the “OFF” position.

10) Remove the black protection cap by hand from the high-low knob (Fig.1).

Fig. 1

11) Insert a 5/32” or 4mm Allen wrench into the hexagonal key-way of the screw (Fig. 2), rotate it counter- clockwise until it is free and extract it.

Fig.2

12) Check that the screw is clean and if necessary remove dirt.

13) Flip the screw (Fig. 3).

Fig.3

Hampton® H35 Direct Vent Freestanding Gas Stove

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Models H35-NG1 Natural Gas H35-LP1 Propane H35 Direct Vent Gas FireplaceUnit Dimensions HamptonTo the New Owner Table of Contents Copy of Safety Label Safety LabelMA Code CO Detector RequirementsInformation for Mobile Manufactured Homes After First Sale InstallationSpecifications Important Message Save These InstructionsThis includes General Safety InformationInstallation Checklist Clearances to CombustiblesVentilation AIR Locating YourGAS Stove CombustionInstallation PrecautionsSafety Precautions For the Installer Exterior Vent Terminal Locations SV4LB6 Rigid Pipe Venting Components ListCaps Rigid Pipe Venting SystemsAlternate HorizontalVenting Systems Rotating 45O Elbow for Straight Horizontal TerminationsVenting Arrangements Vertical Terminations Systems forDura-Vent Snorkel Termination + H1 With these options, max Horizontal Venting with Two 2 90o Elbows+ V1 With these options, max. total Vertical Venting with Two 2 90o ElbowsAlternate Approved Caps Vertical Termination with CO-LINEAR Flex SystemRequired Parts Straight Vertical TerminationsDV Stove Horizontal Vent KIT A m O u l d be facing Down Nylsidingstandoff Dura-Vent Basic Horizontal Kit # Planning Your Dura-Vent InstallationDURA-VENT Termination KIT Termination CapsSnorkel Terminations DURA-VENT Horizontal InstallationsDiagram 1 Hint Apply silicone to female end Below Grade Snorkel InstallationDURA-VENT Vertical Termination This allows for small adjustments Offset ChartConverting a Factory Built Metal Chimney Appoved for US Installations OnlyCathedral Ceilings High ElevationGAS Connection Valve Description But not overtightenedClockwise to open Counter-clockwise to close LPG Conversion Kit Contains Qty Description Conversion KIT #791-969 from NG to LPInstallation of the DC Sparker for the H35-1 Units Only Installation of the DC Sparker For the P90 Units Only Ground Wire from Kit Burner Orifi ce Conversion KIT to Lower BTU RatingNatural Gas Conversion Kit 740-950 Contains Qty Propane Conversion Kit 740-952 Contains Qty02-44 B 02-56 F LOG SET InstallationOptional Brick Panel 02-46 GNotch Cutout Pins on Rear Log SupportPin Cutout Lava rockSide Tile Inset Double Door InstallationTile Inset Installation Top Tile InsetRemove screws Release catch by Pulling up Door Hinge RemovalInstructions Wiring DiagramsWall Thermostat Remote ControlOperating Instructions Adjusting Flame Height Copy of the Lighting Plate InstructionsAutomatic Convection FAN Operation Maintenance Maintenance InstructionsNormal Operating Sounds GAS Appliances Glass Replacement General Vent MaintenanceFAN Maintenance LOG ReplacementReplacing the Fan Installing Valve AssemblyTo remove valve from valve assembly, continue Removing ValveMain Assembly Parts ListBrick Panel SET Burner & LOG AssemblyHampton H35 Direct Vent Freestanding Gas Stove Hampton H35 Direct Vent Freestanding Gas Stove Conditions WarrantyInstaller Please complete the following information

H35-NG1, H35-LP1 specifications

Hampton Direct has made significant strides in the home heating sector with its innovative products, particularly the H35-NG1 and H35-LP1 models. Both are designed to provide efficient heating solutions suitable for various residential settings.

The H35-NG1 is a natural gas unit, while the H35-LP1 runs on liquid propane, allowing homeowners to choose based on their available energy resources. One of the standout features of both models is their compact design, making them ideal for small spaces or rooms where traditional heaters would be impractical.

Another key characteristic is the user-friendly digital thermostat that comes with each unit. This feature allows homeowners to easily set and adjust their desired temperature, ensuring optimal comfort throughout the day while also promoting energy efficiency. The systems are equipped with smart technology that monitors usage patterns, helping homeowners make informed decisions about their heating needs.

Safety is also at the forefront of Hampton Direct's design. Both models include advanced safety features such as an automatic shut-off mechanism to prevent overheating and a fault detection system that alerts users to any issues. This commitment to safety provides peace of mind for homeowners as they enjoy the warmth provided by these heaters.

Additionally, both the H35-NG1 and H35-LP1 are engineered to minimize noise, ensuring a quiet operation that won't disrupt daily activities. This is particularly beneficial for bedrooms or living areas where a peaceful environment is desired.

The energy efficiency rating of these units is impressive, aligning with modern environmental standards. Homeowners can expect lower utility bills and a reduced carbon footprint as both heaters efficiently convert fuel into heat.

With robust construction materials designed to withstand high temperatures, both models promise durability and longevity with minimal maintenance required. This reliability ensures that consumers will not face frequent replacements, making the H35-NG1 and H35-LP1 sound investments for any home.

In summary, Hampton Direct's H35-NG1 and H35-LP1 models deliver effective and safe heating solutions with an emphasis on energy efficiency, user-friendliness, and quiet operation. Homeowners looking for a dependable heating system will find that these models embody quality and innovation, setting new standards in the home heating industry.
Top Page Image Contents