Regency P33R-LP2, P33R-NG2 installation manual Venting Arrangements Horizontal Terminations

Page 14

INSTALLATION

VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS

SIMPSON DURA-VENT DIRECT VENT GS SYSTEM

or Regency Direct Vent (Flex) for Horizontal Terminations (Propane & Natural Gas)

The diagram shows all allowable combinations of vertical runs with horizontal terminations, using two 90o elbows (two 45o elbows equal one 90o elbow).

A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes.

For horizontal terminations the Regency Direct Vent Flex System (see page 10) may be used for installations with a maximum continuous vent length of 10 ft (3.0m).

Note: Must use optional flue adapter (Part # 510-994) when using Simpson Dura-Vent pipe.

•Maintain a 1-1/4" clearance to combustibles (1-1/2" with Flex).

•Horizontal vent must be supported every 3 feet.

•Firestops are required at each floor level and whenever passing through a wall.

•Simpson Dura-Vent: 4" inner dia., 6-5/8" outer dia.

NOTE: Only the AstroCap (Part #: 946-523), the Dura-Vent Snorkel Termination Cap (Part #: 982 (14") or Part# 981 (36") and the Riser

Vent (Part #: 640-530) are approved for Horizontal Termination installations.

(Dura-Vent System or Regency DV Flex)

Alternate

Horizontal

Termination

Caps

Wherever necessary due to external location of cap, the AstroCap can be replaced with the FPI Riser Vent Termination Cap or the Dura-Vent Snorkel Termination Cap.

14	Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace

Image 14

Contents P33R Zero Clearance Rear Direct Vent Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents Safety Label Save These Instructions InstallationGeneral Safety Information Before YOU StartLocating Your GAS Stove Unit DimensionsChecklist Duct System OptionFire hazard is an extreme risk if Clearances Combustible MantelsMantel LEG Clearances These clearances are not adFraming and Finishing Top Facing Support Side Nailing Strips Unit Assembly Prior to InstallationTop Standoff Assembly Screw PositionVent Air supply outletVenting Introduction Regency Direct Vent System Flex Horizontal Terminations onlyInstallation Procedures For Regency Direct Vent System FlexSimpson Dura-Vent Direct Vent GS Simpson DURA-VENT VentingSimpson DURA-VENT Venting Components List Parts not supplied by Dura-VentVenting Arrangements Horizontal Terminations Dura-Vent System or Regency DV FlexVenting Arrangements Vertical Terminations Propane & Natural GasAlternate Approved Caps Vertical Termination With CO-LINEAR Flex SystemRequired Parts Installation Horizontal Installations Snorkel TerminationsGAS Line Installation Vertical TerminationHigh Elevation Pilot AdjustmentGAS Pipe Pressure Testing T. Valve DescriptionConversion Kit Contains Rear Log SupportLOG SET Installation Optional Brick PanelsStandard Flush Door Optional Flush TrimOptional BAY Door Flush LouversDouble Screen Door Thermostat Wire Table Optional Wall Thermostat Remote ControlOptional Wall Switch BAY LouversWiring Diagram Do not cut the ground terminal off under any circumstancesInstalling the Optional FAN Secure left side with 2 screwsOperating Instructions Copy of the Lighting Plate InstructionsAeration Adjustment Lighting ProcedureShutdown Procedure Operating InstructionsMaintenance Thermocouple Flush Glass Replacement Bay Glass ReplacementThermopile Glass GasketShut off the gas supply Installing ValveRemoving Valve Parts List DescriptionBurner & Log Assembly Flush Front & Louvers Bay Front & Louvers Page Page Warranty Warranty LifetimeInstaller Please complete the following information