SAFETY LABEL
| This is a copy of the label that accompanies |
| each |
INSTALLATION | Gas Fireplace. We have printed a copy of the |
contents here for your review. The safety label | |
the correct one. | |
| is located on the right hand side of the unit, |
| visible when the exterior right side brick panel |
| is removed. |
| NOTE: Regency® units are constantly being |
| improved. Check the label on the unit and if |
| there is a difference, the label on the unit is |
|
|
COPY OF SAFETY DECAL
For the State of Massachusetts, installation and repair must be done by a plumber or gasfi tter licensed in the Commonwealth of Massachusetts.
For the State of Massachusetts, fl exible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appli- ances individual manual
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ETIQUETTE`
322
Serial No. / No de serie
Listed: VENTED GAS FIREPLACE
Tested to: ANSI
NATURAL GAS FIREPLACE: MODEL L900E-NG
Factory Equipped For Altitude 0-4500ft. (0-1372m)
L900ENG- Model/Modele: | Min. Supply Pressure | 5“ | WC | (1.25 kpa) |
| ||||
| Low Setting Man. Pressure | 1.6" | WC | (0.39 kpa) |
| Max. Manifold Pressure | 3.5" | WC | (0.87 kpa) |
| Orifice Size (Front Burner) | #47 | DMS |
|
| Orifice Size (Back Burner) | #30 | DMS |
|
| Minimum Input | 11,000 | Btu/h | (3.22 kW) |
| Maximum Input | 48,000 | Btu/h | (14.06 kW) |
| PROPANE GAS FIREPLACE: MODEL | ||||
L900ELP- Model/Modele: | Factory Equipped For Altitude | ||||
Min. Supply Pressure | 12" | WC | (2.98 kpa) | ||
| |||||
| Low Setting Man. Pressure | 3.6" | WC | (0.9 kpa) | |
| Max. Manifold Pressure | 10" | WC | (2.49 kpa) | |
| Orifice Size (Front Burner) | #56 | DMS |
| |
| Orifice Size (Back Burner) | #50 | DMS |
| |
| Minimum Input | 9,500 | Btu/h | (2.78 kW) | |
| Maximum Input | 46,500 | Btu/h | (13.62 kW) | |
VENTED GAS FIREPLACE
This appliance must be installed in accordance with the manufacturer’s installation instructions and with local codes, if any; if none, follow the current ANSI Z223.1 in the USA or the current CAN
This vented gas fireplace is not for use with air filters.
For Manufactured Home Installation: This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280, or the current Standard for Fire Safety Criteria for Manufactured Home Installation, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240 MH Mobile Home Standard in Canada.
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See owner's manual for details. This appliance is not convertible for use with other gases, unless a certified kit is used (Kit
Certified for use with Heat Wave (Kit
Electrical Supply: 120 V, 0.22 A, 60 Hz
NOT FOR USE WITH SOLID FUEL
Minimum Clearances to Combustibles from Fireplace
Side Walls | *A | 16" | (406mm) |
|
|
|
|
|
| ||||
Ceiling | B | 49" | (1245mm) |
| B |
|
Min. Mantel Height | C |
|
| |||
| D | F | ||||
Max. Mantel Depth | **D | 13” | (330mm) |
|
| |
|
|
| ||||
Alcove Width | E | 84" | (2134mm) |
| A |
|
Alcove Depth | F | 36" | (914mm) | C | I |
|
|
|
|
|
|
| |
|
| H |
| |||
| G E |
| ||||
Hearth Height | G | 2" | (51mm) |
|
| |
|
|
| ||||
Hearth Width | H | (841mm) |
|
|
| |
*Alcove side wall must have a min. of 16” (406mm) clearance on one side.
**Mantel depth taken at
FPI Fireplace Products International Ltd., Delta BC, CANADA |
|
MADE IN CANADA / FABRIQUE AU CANADA |
4 | Regency® L900E Direct Vent Gas Fireplace |