Regency L900E-NG installation manual L676 & L900 Direct Vent Fireplace

INSTALLATION

INSTALLATION

Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.

Description		Simpson		Simpson		Selkirk	Metal-Fab®
			®	Direct Vent GS®
		Direct Vent Pro		Discontinued		Direct-Temp™	Sure Seal
Round Support / Radiation Sheild		N/A		N/A		N/A	N/A
Flat Flashing		N/A		N/A		N/A	N/A
Attic Insulation Shield 12”		58DVA-IS - N/A from FPI		58DVA-IS - N/A from FPI		N/A	N/A
Basic Horizontal Termination Kit (A)		N/A		N/A		5DT-HKA	N/A
Horizontal Termination Kit (B)		58DVA-KHA		N/A		5DT-HKB	N/A
Vertical Termination Kit		58DVA-VCH		1291		5DT-VKC	N/A
High Wind Vertical Cap		N/A		N/A		N/A	N/A
High Wind Horizontal Cap		DISC.		1285		N/A	N/A
Horizontal Square Termination Cap		N/A		1284		5DT-HHC	5DHT
Vertical Termination Cap		N/A		N/A		5DT-HVC	5DVT
Storm Collar		58DVA-SC		1253		5DT-SC	5DSC
Adjustable Flashing, 0/12-6/12		58DVA-F6		1243		5DT-AF6	5DF
Adjustable Flashing, 6/12-12/12		58DVA-F12		1243S		5DT-AF12	5DF-12
Vinyl Siding Standoff		58DVA-VSS		1250		5DT-VS	5DVS
Vinyl Siding Shield Plate		N/A		N/A		5DT-VSP	N/A
Snorkel Termination 14”		58DVA-SNK14		1282		5DT-ST14	5DST14
Snorkel Termination 36”		N/A		1281		5DT-ST36	5DST36
Restrictor Disk		58DVA-RD		N/A		N/A	N/A
Colinear Flex Liner Adapter (3” Ø)		N/A		N/A		N/A	N/A
FPI
946-604/P	Simpson Direct Vent Vent Guard (Optional)			946-623/P	AstroCap XL Horizontal Cap
770-994	Rigid Pipe Adapter (Must use with all Rigid Piping)			946-506/P	Vent Guard (Optional)
				946-625	Vinyl Siding Standoff - AstroCap XL

*NOTE: When using Metal-Fab Sure Seal Rigid Piping please note that either the Adaptor (5DDA) or 90º Starter Elbow (5D90A) must be used in conjunction with FPI Rigid Pipe Adaptor (770-994).

L676 & L900 Direct Vent Fireplace

IMPORTANT NOTE

•A Vent Guard is required when the AstroCap is installed above grade at 7 feet or lower.

•The Simpson Dura-Vent and Selkirk Direct Temp horizontal termination caps cannot be used in any applications.

•Only the AstroCap XL and Snorkels are certified for horizontal terminations.

Offset Pipe Selection:

Use this table to determine offset pipe lengths.

Pipe Length	5” x 8” Venting
	Run (X)	Rise (Y)
0”(0mm)	5-11/16”(144mm)	15-5/16”(389mm)
6”(152mm)	8-13/16”(224mm)	18-7/16”(468mm)
9”(229mm)	10-15/16”(278mm)	20-9/16”(522mm)
12”(305mm)	13”(330mm)	22-11/16”(576mm)
24”(610mm)	21-7/16”(697mm)	31-1/16”(789mm)
36”(914mm)	29-13/16”(757mm)	39-7/16”(1002mm)
48”(1219mm)	38-1/4”(972mm)	47-7/8”(1216mm)

L

Y

X

For specific instructions or details on particular venting components please visit the following websites:

Simpson Direct Vent Pro: www.duravent.com

Selkirk Direct-Temp: www.selkirkcorp.com

Metal-Fab Sure Seal: www.mtlfab.com

NOTE: Horizontal runs of vent must be level, or have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present a possible fire hazard.

18 Regency® L900E Direct Vent Gas Fireplace