Integra DTR-7.4 instruction manual Connecting to Audio/Video Equipment, DVD player

Connecting to Audio/Video Equipment—Continued

Connecting a DVD Player (DVD)	Connecting a Video Cassette
	Recorder (VIDEO 1)

IN

R

L

ANTENNA

AUDIO

VIDEO

S VIDEO

VIDEO

COMPONENT

DIGITAL

PRE OUT

COMPONENT

VIDEO

COAX

FRONT

Y

MONITOR

OUTPUT

1

OUT

2

R

L

ZONE 2

PB

INPUT 1

SUB

CENTER

AM

OUT

SURR

Y

3

IN

DVD

PR

SURR

R

L

OPT

BACK/

INPUT 1

ZONE 2

FM

1

75

OUT

Y

VIDEO 1

2

FRONT

MULTI CH

IN

PB

PB

R

INPUT

AUDIO

L

R

L

SUB

CENTER

3

PHONO

OUT

PR

IN

DIGITAL

AUDIO

VIDEO

IN

VIDEO 2

SURR

S VIDEO

INPUT 2

IN

DIGITAL

CD

Y

IN

PR

OPT

OUT

OUT

R

L

COAX

1

BACKR

L

TAPE

IN

VIDEO 3

PB

SURR

2

IN

VIDEO 4

PR

1

GND

AUDIOIN

IN

DVD

S VIDEO

R

L

R

AUDIO

L

VIDEO

DIGITAL

PRE OUT

ANTENNA

AUDIO

VIDEO

S VIDEO

COMPONENT

IN

R

L

VIDEO

COAX

FRONT

MONITOR

OUTPUT

1

OUT

Y

R

L

2

SUB

CENTER

AM

OUT

ZONE 2

PB

SURR

3

IN

DVD

PR

SURR

R

L

OPT

BACK/

INPUT 1

ZONE 2

FM

1

75

OUT

Y

VIDEO 1

2

FRONT

MULTI CH

IN

PB

R

INPUT

AUDIO

L

R

L

SUB

CENTER

3

PHONO

OUT

PR

AUDIO

IN

VIDEO 2

S VIDEO

DIGITAL

VIDEO

SURR

INPUT 2

CD

IN

Y

OUT

R

IN

OPT

R

L

L

OUT

1

IN

VIDEO 3

PB

SURR

BACK

TAPE

OUT IN

2

IN

VIDEO 4

PR

GND

R

L

R

L

SVIDEO 1

VIDEO

AUDIO

AUDIO

IN

DIGITAL	R	L
OUT	AUDIO		VIDEO	S VIDEO
COAX		OUT	OUT	OUT

Y PB PR

COMPONENT

VIDEO

OUTPUT

DVD player

Using an RCA video connection cable, connect the video output jack (composite) of the DVD or LD player to the DVD VIDEO IN jack of the DTR-7.4. Or if the DVD or LD player has an S video output jack, connect it to the DVD S VIDEO IN jack with an S video connection cable. Or if the device has component video outputs, connect them to one of the banks of COMPONENT VIDEO INPUT jacks on the DTR-7.4.

On the initial settings of the DTR-7.4, the DVD input source is set for the COMPONENT VIDEO INPUT 1 jacks.

If you connect the DVD or LD player to the COMPONENT VIDEO INPUT 2 jacks, this must be changed at Setup Menu → Input Setup → Video Setup

→Component Video (See page 38).

Using an RCA audio connection cable, connect the audio output jacks of the DVD or LD player to the DVD AUDIO IN jacks of the DTR-7.4. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a digital output, connect it to either the DIGITAL IN COAX jack or DIGITAL IN OPT jack of the DTR-7.4, depending on the type of connector on the DVD player.

On the initial settings of the DTR-7.4, the DVD input source is set for digital input at the COAX 1 jack. If the digital connection is made at a different jack, this must be changed at Setup Menu → Input Setup → Digital Setup (See page 36).

Make sure of your DVD player’s digital output settings. You need to access the On Screen Menu of your DVD player. See the owner’s Manual on your DVD player. Also, you need to aware of the Table of contents for the movie, selecting the movie for Dolby Digital or DTS, depends how the movie is encoded.

R	L	VIDEO	S VIDEO	R	L	VIDEO	S VIDEO
AUDIO IN		IN	IN	AUDIO OUT		OUT	OUT

VCR

Using RCA video connection cables, connect the video output jack (composite) of the video cassette recorder to the VIDEO 1 VIDEO IN jack of the DTR-7.4 and connect the video input jack of the video cassette recorder to the VIDEO 1 VIDEO OUT jack of the DTR-7.4. Or if the video cassette recorder has S video input and output jacks, connect them to the VIDEO 1 S VIDEO IN and OUT jacks of the DTR-7.4 using S video connection cables. Or if the video cassette recorder has component video outputs, connect them to one of the banks of COMPONENT VIDEO INPUT jacks on the DTR-7.4.

On the initial settings of the DTR-7.4, the VIDEO 1 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the video cassette recorder to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at Setup Menu → Input Setup → Video Setup

→Component Video (See page 38).

Using RCA audio connection cables, connect the audio output jacks of the video cassette recorder to the VIDEO 1 AUDIO IN jacks of the DTR-7.4 and connect the audio input jacks of the video cassette recorder to the VIDEO 1 AUDIO OUT jacks of the DTR-7.4. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If you are connecting a digital output device to the VIDEO 1 jack instead of a VCR, connect it to either the DIGITAL IN COAX jack or DIGITAL IN OPT jack, depending on the type of connector on the device.

On the initial settings of the DTR-7.4, the VIDEO 1 input source is set for digital input at the COAX 2 jack.

If the digital connection is made at a different jack, this must be changed at Setup Menu → Input Setup → Digital Setup (See page 36).

Facilities and Connections

21