Integra DTR-7.4 instruction manual Index Parts and Facilities

Index Parts and Facilities—Continued

For further operational instructions, see the pages indi- cated in brackets [ ].

1Standby/On button [27]

This button is used to set the DTR-7.4 to On or Standby. In the standby state, the display is turned off and the DTR-7.4 cannot be operated.

2Standby indicator [7, 27]

Lights when the DTR-7.4 is in the standby state and when a signal is received from the remote control- ler.

3Audio Selector button [43, 65]

Press to select the type of audio input signal.

4Direct/Pure Audio button [46, 65]

Press to switch between the direct and pure audio listening modes.

5Remote control sensor [7]

6Display button [42]

Press to display information about the current input source signal. Each time you press the Display but- ton, the screen changes to show you different infor- mation concerning the input signal.

7Dimmer button [41]

Press to set the brightness of the front display. There are three settings available: normal, dark, and very dark. The brightness of the front display can also be changed using the remote controller.

8Stereo button [46]

Selects for the stereo listening mode.

9Surround button [46]

Selects for the Dolby Pro Logic II, DTS Neo:6, Dolby Digital, or DTS listening modes.

0THX button [47]

Selects for the THX listening mode.

ADSP / buttons [47]

Switches to the DSP (Digital Signal Processing) modes.

BFront display

CMemory button [49]

Press to assign the radio station to which you are currently tuned to a preset channel or press to delete a previously preset station.

DFM Mode button [48, 49]

Press to change the stereo mode from AUTO to MONO and vice versa. Each time this button is pressed, the AUTO indication turns on and off indicat- ing the current mode. If you are listening to an FM radio station in stereo and the sound cuts out or there is a great deal of noise, switch from AUTO to MONO.

E Tuning / buttons [48]

These buttons used to tune into radio stations and to select items on the onscreen setup menus (OSD).

Preset / buttons [49]

These buttons are used to select radio presets and to select items on the onscreen setup menus (OSD).

FRec Out button [50, 51]

This button is used to select the input source that you want to record via the REC OUTs (i.e., TAPE OUT, VIDEO 1 OUT, VIEDO 2 OUT).

Zone 2 button [68]

This button is used to select the input source for Zone 2.

Off button [68]

This button is used to turn off the REC OUTs (i.e., TAPE OUT, VIDEO 1 OUT, VIDEO 2 OUT) or Zone 2.

GSetup button [29]

Press to enter the Setup Menu. The OSD Menu will appear on the TV monitor as well as the front dis- play on the DTR-7.4.

HEnter button [29]

Press to display the screen for the item that is selected in the Setup Menu.

IReturn button [29]

In the Setup Menu, press to go back one level. If pressed while at the Main Menu, you will exit the Setup Menu.

JMaster Volume dial [40, 65]

Use to control the volume in the main zone. The vol- ume for the remote zone (Zone 2) is independent.

KVideo 5 Input terminals [23]

For connecting a video camera or game device.

LInput source buttons and indicators (DVD, Video 1–5, Tape, Tuner, Phono, CD, and Net Audio) [35, 36, 40]

Press these buttons to select the input source for the main zone.

To select the input source for the remote zone (Zone 2) or recording out (REC OUT), first press the Zone 2 or Rec Out button, and then press the desired input source button. The input channel with its indi- cator lit red is output to REC OUT and the one with its indicator lit green is output to ZONE 2.

MUpsampling indicator [55]

Lights during upsampling. This function is available when the input source is Analog/PCM and the lis- tening mode is set to the stereo or surround mode.

NPhones jack [40]

This is a standard stereo jack for connecting stereo headphones.

OPure Audio indicator [46]

Lights during pure audio playback.

Facilities and Connections

9