Integra DTR-7 instruction manual Setting the speaker configuration, Using the on-screendisplay

Page 19

Setting the speaker configuration

Setting the speaker configuration

3

** Speaker Setup **

Config Setup

Distance Setup

Level Setup

Bass Peak Setup

4

* Config Setup *

All Channel For

THX Speakers =No

5

* Config Setup *

Subwoofer =Yes

Front =Small

Center =Small

Surround =Small

•Using the on-screen display

1.Press the OSD MENU button.

2.Select “Speaker Setup” and then press the right edge of the ENTER/Cursor button.

3.Select “Config Setup” and then press the right edge of the ENTER/Cursor button.

4.For the DTR-6, go to the next step.

For the DTR-7, the display shows “All Channel For THX Speakers.”

Select “Yes” and then press the center of the ENTER/Cursor button. This sets all the connected speakers to THX speakers.(The following steps are unnecessary.)

Select “No” and then press the center of the ENTER/Cursor but- ton to go to the next step.

5.Press the upper or lower edge of the ENTER/Cursor button to set each item and then press the right or left edge of the button to set a parameter

Subwoofer: Set whether or not a subwoofer is connected.

Yes:	A subwoofer is connected.
No:	A subwoofer is NOT connected.

Front : Select the size of your front speakers.

Large: Large front speakers are used.

Small: Small front speakers are used.

Center : Select the size of your center speaker.

Large: A large center speaker is used.

Small: A small center speaker is used.

None: A center speaker is NOT used.

Surround : Select the size of your surround speakers. Large: Large surround speakers are used.

Small: Small surround speakers are used.

None: Surround speakers are NOT used.

6.Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode.

19

Image 19

Contents Appendix Before usingPreparation OperationAVIS Important SafeguardsNote to CATV system installer Precautions1. Warranty Claim 5.PowerAluminum volume control FeaturesSupplied accessories Key FeaturesInstalling the remote controller batteries Before operating this unitUsing the remote controller have been made Audio equipment connectionsDo not plug in the power cord until all connectionsConnections for remote control z Audio equipment connectionsAC outlet connection Video equipment connections Connecting equipment with 5.1-channeloutput Video equipment connectionsDecoder with 5.1-channeloutput Speaker placement Connecting speakersCENTER SPEAKER Connecting speakersFRONT SPEAKERS SURROUND SPEAKERSConnecting power amplifiers Connecting power amplifiersConnecting speakers Connecting a subwooferConnecting the power Connecting an equalizer DTR-7Connecting the power Connecting a power cableAssembling the AM loop antenna Making antenna connectionsConnecting the antenna cable Directional IinkageConnecting an AM outdoor antenna Making antenna connectionsConnecting the included antennas Connecting an FM outdoor antennaHow to use the on-screendisplay Using the on-screendisplayScreen Setup OSD screens Using the on-screendisplaySetting the speaker configuration parameters Setting the speaker configurationFront Center SurroundUsing the on-screendisplay Setting the speaker configurationUsing the on-screendisplay Setting the speaker distanceLoudspeaker Position Time Synchronization R-Sur Setting the speaker LevelCenter RightSetting the bass peak level Setting the Speaker levelBass Peak Level Manager* DTR-7only Digital input setup Playing a digital source Digital Input SetupSetting the Speaker level Using the on-screendisplayTuning in a radio station Presetting FM/AM radio stationsCancelling preset stations Presetting FM/AM radio stationsProgramming radio stations 3. Start playing the selected input source Selecting an input sourceSelecting an input source Selecting an input source COAXIAL Digital Input SetupUsing the on-screendisplay Selecting an input sourceSelecting the speaker system Selecting an input sourceChanging the display Selecting an input source Adjusting the tone Bass and treble adjustmentUsing the on-screendisplay Selecting a preset stationSetting the MULTI CHANNEL INPUT Playing a multichannel input sourceUsing the on-screendisplay Listening Modes Using the Listening ModesBefore Using Listening Mode DSP Digital Signal Processor2. Listening mode button Using the listening modes3. MASTER VOLUME control knob 3. VOLUME buttonsUsing the listening modes Using the listening modesInput sources and listening modes Using the listening modesHow to set the listening mode parameters Setting the listening mode parametersUsing the on-screendisplay Late Night Setting the listening mode parametersListening mode parameters Re-EQCinema Re-EqualizationPHONO Video Assign SetupVideo Assign Setup Using the on-screendisplayTo erase a name Giving a name to each preset radio stationGiving a name to each input source To change a name3.Repeat the operation described in step Fine-tuningthe output level of each speakerTo use the above setting from now on 1.Press the CH LEVEL buttonUsing the on-screendisplay Other setup operationsVolume display method setup IntelliVolume setupRecording a source Recording a source while listening to music or amovie Recording from on audio /video sourceUsing the on-screendisplay Recording a sourceAdding sound to a video tape Outline of Multi-roomRemote System Using Multi-RoomRemote SystemEnjoying Music and Movies in the Sub-room When the system is mounted in a rack Enjoying Music and Movies in the Sub-roomTo control the system in the sub-room Distance Setup The initial settingsInitial settings Config Setupindicator Using the remote controllerUsing the RC-392Mto control each device Turning the power on and off to the receiverControlling an Onkyo/Integra CD player Using the remote controllerControlling an Onkyo/Integra DVD player MODE SAT, CABLE, VCR, and TV buttons Using the remote controllerControlling an Onkyo/Integra MD recorder Controlling an Onkyo/Integra tape deckProgramming procedure Erasing a learned code from a MODE button Erasing a learned codeProgramming Macro mode Using a Macro function2 1 What is a Macro function?Macro Direct Learning function Using a Macro functionUsing a Macro function 1.Open the battery cover and remove the batteries Using a Macro function3.Press the ENT button Remedy Troubleshooting guideTrouble CauseOthers Troubleshooting guideFM/AM Video & audioDTR-7 SpecificationsDTR-6 DTR-7 SpecificationsREMOTE CONTROL REMOTE CONTROLFront panel Control positions and namesDisplay 22 21 20 19 Control positions and namesRemote controller 1 2 3 4 5 6 7 8 9Williams Drive, Ramesy, N.J. 07446, U.S.A ONKYO U.S.A. CORPORATIOND9907-1