Integra DTR-7 instruction manual Making antenna connections, Connecting the included antennas

Page 15

Making antenna connections

Making antenna connections

ANTENNA

AM

FM 75

Remove the insulation at the end of the cable, then fully insert the stripped end of the cable.

ANTENNA

AM

FM 75

Connecting the included antennas

Connecting the FM indoor antenna:

The FM indoor antenna is for indoor use only. Extend the antenna and move it in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion.

If the reception is not very clear with the attached FM indoor an- tenna, the use of an outdoor antenna is recommended.

Connecting the AM loop antenna:

The AM loop antenna is for indoor use only. Set it in the direction and position where you receive the clearest sound. Put it as far away as possible from the unit, TVs, speaker cables, and power cords.

When reception is not satisfactory with the attached AM loop an- tenna alone, connection of an outdoor antenna is recommended.

Connecting an FM outdoor antenna

Please make sure that you follow the considerations below regard- ing the location.

Keep the antenna away from noise sources (neon signs, busy roads, etc.).

It is dangerous to put the antenna close to power lines. Keep it well away from power lines, transformers, etc.

•To avoid the risk of lightning and electrical shock, grounding is necessary. Follow item 19 of the “Important Safeguards” on page 2 when you install the outdoor antenna.

ANTENNA

AM

FM 75

Outdoor antenna

Connecting an AM outdoor antenna

The outdoor antenna will be more effective if it is stretched horizon- tally above a window or outside.

•Do not remove the AM loop antenna.

•To avoid the risk of lightning and electrical shock, grounding is necessary. Follow item 19 of the “Important Safeguards” on page 2 when you install the outdoor antenna.

15

Image 15

Contents Appendix Before usingPreparation OperationAVIS Important SafeguardsNote to CATV system installer Precautions1. Warranty Claim 5.PowerAluminum volume control FeaturesSupplied accessories Key FeaturesBefore operating this unit Installing the remote controller batteriesUsing the remote controller have been made Audio equipment connectionsDo not plug in the power cord until all connectionsAudio equipment connections Connections for remote control zAC outlet connection Video equipment connections Video equipment connections Connecting equipment with 5.1-channeloutputDecoder with 5.1-channeloutput Speaker placement Connecting speakersCENTER SPEAKER Connecting speakersFRONT SPEAKERS SURROUND SPEAKERSConnecting power amplifiers Connecting power amplifiersConnecting speakers Connecting a subwooferConnecting the power Connecting an equalizer DTR-7Connecting the power Connecting a power cableAssembling the AM loop antenna Making antenna connectionsConnecting the antenna cable Directional IinkageConnecting an AM outdoor antenna Making antenna connectionsConnecting the included antennas Connecting an FM outdoor antennaUsing the on-screendisplay How to use the on-screendisplayScreen Setup OSD screens Using the on-screendisplaySetting the speaker configuration parameters Setting the speaker configurationFront Center SurroundUsing the on-screendisplay Setting the speaker configurationSetting the speaker distance Using the on-screendisplayLoudspeaker Position Time Synchronization R-Sur Setting the speaker LevelCenter RightSetting the Speaker level Setting the bass peak levelBass Peak Level Manager* DTR-7only Digital input setup Playing a digital source Digital Input SetupSetting the Speaker level Using the on-screendisplayTuning in a radio station Presetting FM/AM radio stationsPresetting FM/AM radio stations Cancelling preset stationsProgramming radio stations 3. Start playing the selected input source Selecting an input sourceSelecting an input source Selecting an input source COAXIAL Digital Input SetupUsing the on-screendisplay Selecting an input sourceSelecting an input source Selecting the speaker systemChanging the display Selecting an input source Adjusting the tone Bass and treble adjustmentUsing the on-screendisplay Selecting a preset stationPlaying a multichannel input source Setting the MULTI CHANNEL INPUTUsing the on-screendisplay Listening Modes Using the Listening ModesBefore Using Listening Mode DSP Digital Signal Processor2. Listening mode button Using the listening modes3. MASTER VOLUME control knob 3. VOLUME buttonsUsing the listening modes Using the listening modesInput sources and listening modes Using the listening modesSetting the listening mode parameters How to set the listening mode parametersUsing the on-screendisplay Late Night Setting the listening mode parametersListening mode parameters Re-EQCinema Re-EqualizationPHONO Video Assign SetupVideo Assign Setup Using the on-screendisplayTo erase a name Giving a name to each preset radio stationGiving a name to each input source To change a name3.Repeat the operation described in step Fine-tuningthe output level of each speakerTo use the above setting from now on 1.Press the CH LEVEL buttonUsing the on-screendisplay Other setup operationsVolume display method setup IntelliVolume setupRecording a source Recording a source while listening to music or amovie Recording from on audio /video sourceRecording a source Using the on-screendisplayAdding sound to a video tape Using Multi-RoomRemote System Outline of Multi-roomRemote SystemEnjoying Music and Movies in the Sub-room Enjoying Music and Movies in the Sub-room When the system is mounted in a rackTo control the system in the sub-room Distance Setup The initial settingsInitial settings Config Setupindicator Using the remote controllerUsing the RC-392Mto control each device Turning the power on and off to the receiverUsing the remote controller Controlling an Onkyo/Integra CD playerControlling an Onkyo/Integra DVD player MODE SAT, CABLE, VCR, and TV buttons Using the remote controllerControlling an Onkyo/Integra MD recorder Controlling an Onkyo/Integra tape deckProgramming procedure Erasing a learned code from a MODE button Erasing a learned codeProgramming Macro mode Using a Macro function2 1 What is a Macro function?Macro Direct Learning function Using a Macro functionUsing a Macro function Using a Macro function 1.Open the battery cover and remove the batteries3.Press the ENT button Remedy Troubleshooting guideTrouble CauseOthers Troubleshooting guideFM/AM Video & audioSpecifications DTR-7DTR-6 DTR-7 SpecificationsREMOTE CONTROL REMOTE CONTROLControl positions and names Front panelDisplay 22 21 20 19 Control positions and namesRemote controller 1 2 3 4 5 6 7 8 9ONKYO U.S.A. CORPORATION Williams Drive, Ramesy, N.J. 07446, U.S.AD9907-1