Integra DTR-7 instruction manual Recording a source while listening to music or a, movie

Recording a source

SMART SCAN CONTROLLER

	FM MUTE/			CHARACTER/	SP/SYS	AUDIO	BASS/
DIMMER	MODE	DOWN TUNING	UP	MEMORY	SETUP	ADJUSTMENT	TREBLE

STANDBY/ON
							MODE
							PRESET/MODE ADJ
STANDBY MULTI SOURCE						SMART SCAN
						CONTROLLER
POWER
							PUSH TO ENTER
ON OFF
				LISTENING MODE			REC OUT/	DIGITAL/
A SPEAKERS B
	DISPLAY	DIRECT	STEREO	/DTS	THX	DSP	MULTI SOURCE	ANALOG	CH LEVEL

MASTER VOLUME

		W	N
D	O

U

P

					SURROUND		MODE
PHONES	MULTI CH INPUT						VIDEO4 (MONO)
	DVD	VIDEO-1	VIDEO-2	VIDEO-3	VIDEO-4	TAPE	FM

AM

PHONO C D

S VIDEO VIDEO L AUDIO R

DTR-7 by

Input selector buttons REC OUT

1										Recording a source while listening to music or a
										movie
DVD	VIDEO-1	VIDEO-2	VIDEO-3	VIDEO-4	TAPE	FM	AM	PHONO	C D	1. Select the source you wish to play (recording source) by
										pressing the corresponding input selector button.
										See step 1 of “Selecting an input source” (page 26).
										2. Press the REC OUT button.
										The REC OUT indicator blinks for 8 seconds.
2										While the REC OUT indicator is blinking, rotate the SMART
					REC OUT					SCAN CONTROLLER until "SOURCE" appears.
REC OUT										Notes:
										• For DTR-7, The digital input signals assigned to the input source you
										selected using the input selector buttons will be output to the DIGITAL
										OUTPUT terminal. There are some restrictions on digital recording.
										When making digital recordings, consult the instruction manual that
										came with your digital recording equipment (such as MD recorder or
3										DAT deck) to know what restrictions are imposed.
										• You cannot select the source connected to the MULTI CHANNEL IN-
PRESET/MODE ADJ										PUT connectors. Even if you press the MULTI CH INPUT button in
										step 1 above, the signals will be output to the L and R output jacks of the
			SPEAKERS REC OUT				STEREO			input source you selected most recently.
			A
										4. Start recording on the recorder connected to the TAPE,
PUSH TO ENTER										VIDEO-1, VIDEO-2 jacks. Then, start playing the source
										component you selected in step 1.
										Notes:
										• If you change the input source during recording, you will record the
										signals from the newly selected input source.
										• You cannot record the surround effects.

1			Recording from on audio /video source
	REC OUT	REC OUT	1.	Press the REC OUT button
				The REC OUT indicator binks for 8 seconds
			2.	While the REC OUT indicator is blinking, rotate the
				SMART SCAN CONTROLLER to select the desired re-
2				cording source.
	PRESET/MODE ADJ		Notes:

• Selecting "SOURCE" sets the currently selected input source as the re- cording source.

• For DTR-7, The digital input signals assigned to the input source you selected using the input selector buttons will be output to the DIGITAL

PUSH TO ENTEROUTPUT terminal. There are some restrictions on digital recording. When making digital recordings, consult the instruction manual that came with your digital recording equipment (such as MD recorder or DAT deck) to know what restrictions are imposed.

• You cannot select the source connected to the MULTI CHANNEL IN- PUT connectors. Even if you press the MULTI CH INPUT button in step 1 above, the signals will be output to the L and R output jacks of the input source you selected most recently.

3. Start recording on the recorder connected to the TAPE, VIDEO-1, VIDEO-2 jacks. Then, start playing the source component you selected in step 1.

Notes:

• If you change the input source during recording, you will record the signals from the newly selected input source.

• You cannot record the surround effects.

44