Integra DTR-7 Audio equipment connections, AC outlet connection, Connections for remote control z

Audio equipment connections

1.DIGITAL INPUT connectors

•If your CD player has a digital output connector, connect it to a proper DIGITAL INPUT connector for clear and dynamic sound play.

•This unit provides four digital input connectors to connect CD players, MD recorders, DAT decks, etc. having a digital output connector. When using these connectors, connect the unit also via the audio con- nection cables. You should also note that the signals you can record are analog signals only.

•The digital inputs, COAXIAL 1, 2 and OPTICAL 1, 2 can be assigned to individual input selector buttons, so when an input selector button is pressed, the assigned digital input is used instead of the corresponding analog input. (See pages 23,29.)

2.OPTICAL DIGITAL OUTPUT connector (DTR-7 only)

If you have a digital recorder, such as an MD recorder, DAT, and CD-R (Compact Disc Recorder), con- nect the recorder’s digital input connector to this connector. In this case, always use commercially avail- able optical digital audio cables.

3.Turntable

This receiver is designed for use with turntables using moving magnet cartridges. Connect a ground (or earth) wire to GND terminal.

With some players, connecting a ground wire results in larger noise. If so, do not connect any ground wire.

Optical digital connector

Remove the protective caps before making connections. When not in use, be sure to replace them.

DIGITAL INPUT	R	L	R	L	V	S	SURROUND SPEAKERS	FRONT SPEAKERS A
	AMP IN

	FRONT			OUT
COAXIAL				VIDEO-1	ANTENNA
1	PRE OUT				R	L	R	L
	FRONT			IN
COAXIAL
2	SUB
	WOOFER			OUT			CENTER
OPTICAL
1	CENTER			VIDEO-2			SPEAKER
				IN			CAUTION: SPEAKER IMPEDANCE
OPTICAL	SURROUND				R	L	6 OHMS MIN. / SPEAKER
2
	FRONT			VIDEO-3
				IN
OPTICAL
	SUB			DVD	FRONT SPEAKERS B		AC OUTLETS
	WOOFER						AC 120V 60Hz
DIGITAL OUTPUT				IN			SWITCHED
	CENTER				AV RECEIVER		TOTAL 120W 1A MAX.
	SURROUND		(REC)	MONITOR	MODEL NO. DTR-7
	MULTI CHANNEL
	INPUT		OUT	OUT
	R	L	TAPE	�				AC INLET
	CD		IN
			(PLAY)
	GND			VIDEO
	PHONO			S VIDEO
				OSD SELECTOR

R	L	R	L
			LOCAL REMOTE	REMOTE
				CONTROL

Capacity is total 120 watts.

AC outlet connection

You can connect the power cord from another audio device to the rear of this receiver.

Since the AC outlets on the unit are a SWITCHED type outlet, you can use the STANDBY/ON button, to turn on/off the power to both this receiver and the connected audio de- vices.

First turn the POWER switch ON ( ).

Make sure that the total capacity of other compo- nents connected to this unit does not exceed the capacity that is printed on the rear panel.

DTR-7 / DTR-6

DIGITAL INPUT	R	L	R	L	V	S	SURROUND SPEAKERS	FRONT SPEAKERS A
	AMP IN

	FRONT					OUT
COAXIAL					VIDEO-1	ANTENNA
1	PRE OUT
	FRONT					IN	R	L	R	L
COAXIAL						AM
2	SUB
OPTICAL	WOOFER					OUT			CENTER
1	CENTER				VIDEO-2				SPEAKER
						IN			CAUTION: SPEAKER IMPEDANCE
OPTICAL	SURROUND					FM	R	L	6 OHMS MIN. / SPEAKER
2					VIDEO-3	75
	FRONT					IN
OPTICAL
	SUB				DVD				AC OUTLETS
	WOOFER					IN	FRONT SPEAKERS B		AC 120V 60Hz
DIGITAL OUTPUT
						AV RECEIVER			SWITCHED
	CENTER								TOTAL 120W 1A MAX.
	SURROUND			(REC)	MONITOR	MODEL NO. DTR-7
	MULTI CHANNEL
	INPUT			OUT	OUT
	R		L	TAPE	�					AC INLET
					MULTI SOURCE
	CD			IN	OUT
				(PLAY)
	GND				VIDEO
	PHONO				S VIDEO
	R	L	R	L	OSD SELECTOR
						LOCAL REMOTE	REMOTE

CONTROL

CD Player

Cassette Tape Deck

Connections for remote control (z)

You can use the remote controller of this receiver to operate cassette tape decks and compact disc players that have Onkyo/ Integra z connectors.

Connect a remote control cable to the connector with the z mark.

•Anz remote control cable equipped with a 1/8 in. -diam- eter miniature two-conductor phone plug comes with ev- ery compact disc player or cassette tape deck that has an z connector.

•Remote control operation is not possible if only the remote control cable is connected – the audio connection cables must also be connected.

•This receiver’s remote controller does not support control of Onkyo turntables.

•If the connecting device has two z connectors lined-up vertically or horizontally, you can use either of them. They both offer the same functionality.

•You can use the remote controller for the DTR-7/DTR-6 to control an Onkyo/Integra DVD player or MD recorder that is not connected via an z cable. When you control such a DVD player or MD recorder, point the remote controller toward the sensor area of the DVD player or MD recorder.

7